|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
ABS Warning Light | ABS warning light |
ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Brake Warning Light |
Brake warning light / red (malfunction) |
ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| ECB Warning Light |
Brake warning light / yellow (minor malfunction) |
ON or OFF | ON: Warning light on
OFF: Warning light off |
ECB: Electronically Controlled Brake System |
|
Buzzer | Meter buzzer |
ON or OFF | ON: Buzzer on
OFF: Buzzer off | - |
|
Stop Light SW | Stop light switch assembly |
ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Parking Brake SW |
Parking brake switch assembly |
ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| TRC(TRAC)/VSC OFF SW |
VSC OFF switch | ON or OFF |
ON: Switch on OFF: Switch off |
- |
| Reservoir Warning SW |
Brake fluid level warning switch |
ON or OFF | ON: Reservoir level low
OFF: Reservoir level normal |
- |
| Main Idle SW |
Main idle switch | ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
| Shift Lever Position |
Shift position information |
Fail, 1st, 2nd, 3rd, 4th, 5th, 6th/B, D/M, P,N or R |
Actual shift position |
- |
| Inspection Mode |
Inspection mode | Other or Inspect |
Other: Normal mode Inspect: Inspection mode |
- |
| Stroke Sensor |
Brake pedal stroke sensor |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.65 to 1.35 V |
Reading increases when brake pedal is depressed |
|
Voltage of Stroke Sensor |
Voltage of brake pedal stroke sensor |
Min.: -2.50 V, Max.: 2.49 V |
- | - |
|
Stroke Sensor2 | Brake pedal stroke sensor 2 |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 3.65 to 4.35 V |
Reading decreases when brake pedal is depressed |
|
Voltage of Stroke Sensor2 |
Voltage of brake pedal stroke sensor 2 |
Min.: -2.50 V, Max.: 2.49 V |
- | - |
|
Deceleration Sensor | Acceleration sensor 1 |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Deceleration Sensor2 | Acceleration sensor 2 |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele2 | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Yaw Rate Sensor | Yaw rate sensor 1 |
Min.: -128 degrees/s, Max.: 127 degrees/s |
Vehicle stationary: 0 degrees/s Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s |
- |
| Zero Point of Yaw Rate |
Memorized zero value | Min.: -128 degrees, Max.: 127 degrees |
- | After completing zero point calibration: 0 degrees |
|
Yaw Rate Sensor2 | Yaw rate sensor 2 |
Min.: -128 degrees/s, Max.: 127 degrees/s |
Vehicle stationary: 0 degrees/s Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s |
- |
| Steering Angle Sensor |
Steering angle sensor | Min.: -3276.8 degrees, Max.: 3276.7 degrees |
Turning left: Increases Turning right: Decreases |
- |
| Zero Point of Steering Angle |
Memorized zero value | Min.: -3276.8 degrees, Max.: 3276.7 degrees |
- | After clearing zero point calibration: 0 degrees |
|
Lateral G | Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and backward G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
|
Yaw Rate Value | Yaw rate value |
Min.: -128 degrees/s, Max.: 127 degrees/s |
- | During turning: Changes in proportion with yaw |
|
Steering Angle Value | Steering angle value |
Min.: -3276.8 degrees, Max.: 3276.7 degrees |
- | During steering operation: Changes in proportion with steering wheel rotation |
|
Stop Light Relay | Stop light control relay (Stop light switch assembly)
(STP2 terminal input) | ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Slip Indicator Light |
Slip indicator light | ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
| FR Wheel Speed |
Front speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FL Wheel Speed | Front speed sensor LH |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RR Wheel Speed | Rear speed sensor RH |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RL Wheel Speed | Rear speed sensor LH |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
Vehicle Speed | Maximum wheel speed sensor |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FR Wheel Acceleration | Front wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
FL Wheel Acceleration | Front wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
RR Wheel Acceleration | Rear wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
RL Wheel Acceleration | Rear wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Stop Light Relay Output |
Stop light control relay (Stop light switch assembly) (STPO terminal output) |
ON or OFF | ON: Relay output on
OFF: Relay output off |
- |
| FR Wheel ABS Ctrl Status |
Front wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| FL Wheel ABS Ctrl Status |
Front wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| RR Wheel ABS Ctrl Status |
Rear wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| RL Wheel ABS Ctrl Status |
Rear wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| BA Ctrl Status |
BA control status | ON or OFF |
ON: During control | - |
|
PBA Ctrl Status | PBA control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Ctrl Status |
TRAC control status | ON or OFF |
ON: During control | - |
|
TRC(TRAC) Engine Ctrl Status |
TRAC engine control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Brake Ctrl Status |
TRAC brake control status |
ON or OFF | ON: During control |
- |
| FR Wheel VSC Ctrl Status |
Front wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| FL Wheel VSC Ctrl Status |
Front wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| RR Wheel VSC Ctrl Status |
Rear wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| RL Wheel VSC Ctrl Status |
Rear wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| Accelerator Opening Angle % |
Percentage of accelerator pedal opening angle |
Min.: 0.0%, Max.: 127.5% |
Accelerator pedal released: 0.0% |
During accelerator pedal operation: Changes in proportion with the pedal movement |
|
Regenerative Cooperation |
Regenerative cooperation |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
FR Regenerative Request |
FR regenerative request torque |
Min.: 0 Nm, Max.: 1048560 Nm |
- | Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
|
FR Regenerative Operation |
FR regenerative operation torque |
Min.: 0 Nm, Max.: 1048560 Nm |
- | Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
|
Solenoid Relay | ABS solenoid relay operation request |
ON or OFF | ON: Power switch on (IG) (During initial check)
OFF: Power switch off |
- |
| ECB Motor Relay |
Motor relay 1 operation request |
ON or OFF | ON: Relay on
OFF: Relay off | ECB: Electronically Controlled Brake System |
|
ECB Motor Relay2 | Motor relay 2 operation request |
ON or OFF | ON: Relay on
OFF: Relay off | ECB: Electronically Controlled Brake System |
|
ECB Main Relay | Main relay operation request |
ON or OFF | ON: Relay on
OFF: Relay off | ECB: Electronically Controlled Brake System |
|
ABS Solenoid (SFRH) | Holding solenoid valve (FRH) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SFRR) | Reduction solenoid valve (FRR) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SFLH) | Holding solenoid valve (FLH) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SFLR) | Reduction solenoid valve (FLR) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SRRH) | Holding solenoid valve (RRH) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SRRR) | Reduction solenoid valve (RRR) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SRLH) | Holding solenoid valve (RLH) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
ABS Solenoid (SRLR) | Reduction solenoid valve (RLR) |
ON or OFF | ON: Operating
OFF: Not operating | - |
|
FR Speed Open | Front speed sensor RH open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
FL Speed Open | Front speed sensor LH open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
RR Speed Open | Rear speed sensor RH open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
RL Speed Open | Rear speed sensor LH open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Yaw Rate Open | Yaw rate sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Deceleration Open | Acceleration sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Steering Open | Steering angle sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Stroke Open | Brake pedal stroke sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Stroke2 Open | Brake pedal stroke sensor 2 open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Accumulator Open | Accumulator pressure sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
HV Communication Open | Hybrid vehicle communication open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
VCM1 Voltage Value | VCM1 voltage value |
Min.: 0.00 V, Max.: 10.00 V |
6.29 to 7.64 V | - |
|
VCM2 Voltage Value | VCM2 voltage value |
Min.: 0.00 V, Max.: 10.00 V |
6.29 to 7.64 V | - |
|
IG1 Voltage Value | IG1 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
IG2 Voltage Value | IG2 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
BS1 Voltage Value | BS1 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
BS2 Voltage Value | BS2 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
VM1 Voltage Value | VM1 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
VM2 Voltage Value | VM2 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to auxiliary battery voltage |
|
MT Voltage Value | MT voltage value |
Min.: 0.00 V, Max.: 20.00 V |
Pump motor off: 0.00 V Pump motor on: 12.00 V |
- |
| BH Standby Light |
Brake hold standby indicator light |
ON or OFF | ON: Indicator light on
OFF: Indicator light off |
- |
| BH Operated Light |
Brake hold operated indicator light |
ON or OFF | ON: Indicator light on
OFF: Indicator light off |
- |
| TRAC/VSC Off Mode |
TRAC/VSC off mode | Normal, TRC OFF, VSC Expert Mode or VSC OFF |
Normal: Normal mode TRC OFF: TRAC off mode VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode |
- |
| Number of DTC |
Number of DTC | Min.: 0, Max.: 255 |
- | Number of DTCs output is displayed |
|
FR Speed Sensor Voltage Open |
Front speed sensor RH voltage open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
FL Speed Sensor Voltage Open |
Front speed sensor LH voltage open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
RR Speed Sensor Voltage Open |
Rear speed sensor RH voltage open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
RL Speed Sensor Voltage Open |
Rear speed sensor LH voltage open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Yaw Rate Sensor Voltage Open |
Yaw rate sensor voltage open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
SLA Solenoid Current | Linear solenoid addition valve (SLA) current |
Min.: 0.00 A, Max.: 3.00 A |
Brake pedal released: 0.00 to 1.50 A |
- |
| SLR Solenoid Current |
Linear solenoid reduction valve (SLR) current |
Min.: 0.00 A, Max.: 3.00 A |
Brake pedal released: 0.00 to 1.50 A |
- |
| Brake Hold Switch |
Brake hold switch (Electric parking brake switch assembly) |
ON or OFF | ON: Switch on
OFF: Switch off | - |
|
Reaction Force Pressure |
Pressure value of stroke simulator |
Min.: 0.00 MPa, Max.: 24.48 MPa |
Brake pedal released: 0.00 MPa |
Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
|
Servo Pressure | Pressure value of servo |
Min.: 0.00 MPa, Max.: 24.48 MPa |
Brake pedal released: 0.00 to 2.10 MPa |
Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
|
Accumulator Pressure | Accumulator pressure output value |
Min.: 0.00 MPa, Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) |
When
brake fluid is stored in the accumulator: Accumulator pressure changes
in accordance with volume of fluid stored in the accumulator |
|
Reaction Force Pressure Sensor Temperature |
Reaction force pressure sensor temperature |
Min.: -80°C (-112°F), Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) |
- |
| Servo Pressure Sensor Temperature |
Servo pressure sensor temperature |
Min.: -80°C (-112°F), Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) |
- |
| Accumulator Pressure Sensor Temperature |
Accumulator pressure sensor temperature |
Min.: -80°C (-112°F), Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) |
- |
| MT Voltage Value (ABS) |
ABS motor voltage value |
Min.: 0.00 V, Max.: 20.00 V |
ABS motor off: 0.00 V ABS motor on: 11.00 to 14.00 V |
- |
| ECB Solenoid (SGH) |
Switching solenoid valve (SGH) |
ON or OFF | ON: Solenoid on
OFF: Solenoid off | ECB: Electronically Controlled Brake System |
|
ECB Solenoid (SSA) | Switching solenoid valve (SSA) |
ON or OFF | ON: Solenoid on
OFF: Solenoid off | ECB: Electronically Controlled Brake System |
|
Power Supply Voltage Low Light ON Trip Counter |
Number of trips after light illuminated when power supply voltage was low |
Min.: 0, Max.: 255 | - |
- |
| SGH Solenoid Current |
Switching solenoid valve (SGH) current |
Min.: 0.00 A, Max.: 3.00 A |
0.00 to 1.50 A | - |
|
SSA Solenoid Current | Switching solenoid valve (SSA) current |
Min.: 0.00 A, Max.: 3.00 A |
0.00 to 1.50 A | - |
|
Reaction Force Pressure Sensor Open |
Reaction force pressure sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Servo Pressure Sensor Open |
Servo pressure sensor open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
|
Ambient Temperature | Ambient temperature |
Min.: -128°C (-198.4°F), Max.: 127°C (260.6°F) |
-30°C (-22°F) to 100°C (212°F) |
Changes according to ambient temperature |
|
Air Bag ECU Communication Open |
Airbag ECU assembly communication open detection |
Error or Normal | Error: Momentary interruption
Normal: Normal | - |
