MONITOR DESCRIPTION The ECM
continuously monitors its main and sub CPUs. This self-check ensures
that the ECM is functioning properly. If outputs from these CPUs are
different and deviate from the standard, the ECM will illuminate the MIL
and store a DTCs. |
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
MIL | Memory |
Note | | P060604 |
Control Module Processor System Internal Failure |
ECM main CPU malfunction (1 trip detection logic) |
ECM | Comes on |
DTC stored | SAE Code: P0606 | |
P060629 | Control Module Processor Signal Invalid |
ECM main CPU malfunction (1 trip detection logic) |
ECM | Comes on |
DTC stored | SAE Code: P0606 | |
P06062A | Control Module Processor Signal Stuck in Range |
ECM main CPU malfunction (1 trip detection logic) |
ECM | Comes on |
DTC stored | SAE Code: P0606 | |
P060647 | Control Module Processor Watchdog/Safety MCU Failure |
ECM main CPU malfunction (1 trip detection logic) |
ECM | Comes on |
DTC stored | SAE Code: P0606 | MONITOR STRATEGY |
Related DTC | P0606: ECM/PCM processor performance | |
Required Sensors/Components (Main) | ECM | |
Required Sensors/Components (Related) |
- | | Frequency of Operation |
Continuous | | Duration |
2 times | | MIL Operation |
Immediate | | Sequence of Operation |
None | TYPICAL ENABLING CONDITIONS All |
Monitor runs whenever the following DTCs are not stored |
None | Case 1, Case 2 and Case 3 |
Both of the following conditions are met |
- | | Write Inhibit |
Permit | | Time after Write status forbiddance to permit |
0.5 seconds or more | Case 4 and Case 5 |
All of the following conditions are met |
- | | Battery voltage | 8 V or higher | |
Engine switch | On (IG) | | Starter |
Off | | Write Inhibit |
Permit | | Time after Write status forbiddance to permit |
0.5 seconds or more | TYPICAL MALFUNCTION THRESHOLDS Case 1 |
One of the following conditions is met | 5 seconds or more | |
ROM check sum | Error | |
RAM Read/Write check | Fail | |
Specific software routine operation period check | Fail | |
Software functional check | Fail | Case 2 |
Following condition is met | 40 times or more | |
Specific software routine operation period check | Fail | Case 3 |
One of the following conditions is met | A or B | |
A. Following condition is met | More than 30 seconds | |
Specific software operation A validity check |
Fail | | B. Following condition is met |
More than 30 seconds | | Specific software operation B validity check |
Fail | Case 4 |
Following condition is met | 25 times or more | |
DMA communication | No response | Case 5 |
Following condition is met | 8 times or more | |
Watchdog from monitoring processor | Not toggle | |
CPU reset | Occurred | CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the
vehicle has returned to normal by performing the following All Readiness
check procedure.
Click here 
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the Techstream off.
- Turn the engine switch off.
- Disconnect the Techstream.
- Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
- Connect the cable to the negative (-) battery terminal.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Wait 1 second or more [A].
- Enter the following menus: Powertrain / Engine / Trouble Codes [B].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P060604, P060629 or P060647.
- Check the DTC judgment result.
|
Techstream Display |
Description |
|
NORMAL |
- DTC judgment completed
- System normal
|
|
ABNORMAL |
- DTC judgment completed
- System abnormal
|
|
INCOMPLETE |
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
|
HINT:
CAUTION / NOTICE / HINT NOTICE: After
turning engine switch off, waiting time may be required before
disconnecting the cable from the negative (-) battery terminal.
Therefore, make sure to read the disconnecting the cable from the
negative (-) battery terminal notices before proceeding with work. Click here
HINT: Read
freeze frame data using the Techstream. The ECM records vehicle and
driving condition information as freeze frame data the moment a DTC is
stored. When troubleshooting, freeze frame data can help determine if
the vehicle was moving or stationary, if the engine was warmed up or
not, if the air fuel ratio was lean or rich, and other data from the
time the malfunction occurred. PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG). (c) Turn the Techstream on.
(d) Clear the DTC. Powertrain > Engine > Clear DTCs (e) Turn the engine switch off.
|
NEXT |
 | |
| 2. |
READ OUTPUT DTC (DTC P060604, P060629 OR P060647) |
(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) battery terminal. (c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG). (e) Turn the Techstream on.
(f) Wait 1 second or more. (g) Enter the following menus: Powertrain / Engine / Trouble Codes.
(h) Read the DTCs. Powertrain > Engine > Trouble Codes
|
Result | Proceed to | |
DTCs are not output | A | |
DTC P060604, P060629 or P060647 is output |
B |
| A |
 | CHECK FOR INTERMITTENT PROBLEMS |
| B |
| REPLACE ECM | | 
