DATA LIST / ACTIVE TEST DATA LIST NOTICE:
In
the table below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not. HINT: Using
the Techstream to read the Data List allows the values or states of
switches, sensors, actuators and other items to be read without removing
any parts. This non-intrusive inspection can be very useful because
intermittent conditions or signals may be discovered before parts or
wiring is disturbed. Reading the Data List information early in
troubleshooting is one way to save diagnostic time. (a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG). (c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Data List. (e) Read the Data List according to the display on the Techstream. Chassis > LKA/LDA > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
LDA Control | Lane departure alert system (w/ steering control) control status |
Prohibit or Permit | Prohibit: Control prohibited
Permit: Control permitted |
- | | Turn Signal Switch (Right) |
Turn signal switch (right) status |
OFF or ON | ON: Turn signal light switch on (right)
OFF: Turn signal light switch off |
- | | Turn Signal Switch (Left) |
Turn signal switch (left) status |
OFF or ON | ON: Turn signal light switch on (left)
OFF: Turn signal light switch off |
- | | Destination Information |
- | - |
- | This item is displayed on the Techstream but is not used. | |
Left Lane Indicator | Left lane marker detection status |
Nothing, Heavy, Thin or H blink |
Nothing: Lane departure alert system (w/ steering control) deactivated
Heavy: Left lane marker detected Thin: Left lane marker not detected
H blink: Departing from lane |
- | | Right Lane Indicator |
Right lane marker detection status |
Nothing, Heavy, Thin or H blink |
Nothing: Lane departure alert system (w/ steering control) deactivated
Heavy: Right lane marker detected Thin: Right lane marker not detected
H blink: Departing from lane |
- | | Skid Control Buzzer Demand |
Lane departure alert Buzzer Demand Status |
OFF or ON | OFF: Lane departure alert buzzer not operating
ON: Lane departure alert buzzer operating |
- | | Vehicle Information (2WD/4WD) |
- | - |
- | This item is displayed on the Techstream but is not used. | |
Vehicle Information (Conv/HV) |
- | - |
- | This item is displayed on the Techstream but is not used. | |
The Number of DTCs | Number of stored DTCs |
0 to 255 | Number of stored DTCs |
- | HINT: The
Data List will also be displayed when you enter the following menus,
but do not use this: Chassis / LKA/LDA (Sub) / Data List. Chassis > LKA/LDA (Sub) > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Engine / HV Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
DRS Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
Meter Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
Yaw Rate Sensor Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
Steering Angle Sensor Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
EPS Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
VSC Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. | |
VGRS Communication Failure |
- | - |
- | This item is displayed on the Techstream but is not used. |
(f) Enter the following menus: Chassis / Front Recognition Camera / Data List.
(g) Read the Data List according to the display on the Techstream. Chassis > Front Recognition Camera > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Vehicle Information (2WD/4WD) |
Vehicle information (drivetrain) stored in forward recognition camera |
2WD, 4WD or Unknown | 2WD: for 2WD
4WD: for AWD Unknown: Vehicle information not confirmed |
- | | Vehicle Information (Conv/HV) |
Vehicle information (conventional/hybrid) stored in forward recognition camera |
Conv, HV or Unknown | Conv: Conventional
HV: Hybrid vehicle Unknown: Vehicle information not confirmed |
- | ACTIVE TEST HINT:
Using
the Techstream to perform Active Tests allows relays, VSVs, actuators
and other items to be operated without removing any parts. This
non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is
disturbed. Performing Active Tests early in troubleshooting is one way
to save diagnostic time. Data List information can be displayed while
performing Active Tests. (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG).
(c) Turn the Techstream on. (d) Enter the following menus: Chassis / LKA/LDA / Active Test.
(e) Perform Active Test according to the display on the Techstream. HINT:
The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream. Chassis > LKA/LDA > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note | |
LDA Buzzer | Sounds the lane departure alert buzzer |
ON/OFF | Confirm that the vehicle is stopped with the engine switch on (IG). | |
Steering Wheel Vibration |
- | - |
This item is displayed on the Techstream but is not used. |
(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(g) Perform Active Test according to the display on the Techstream. HINT:
The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream. Body Electrical > Combination Meter > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note | |
Multi Display All (White) |
Multi-information display (White display) |
ON | - | | 
