Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Problem Symptoms Table

Either of the following:

• The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 1.
• Resistance between CAN bus lines (CANH and CANL) in Bus 1 is 70 Ω or more.

Open in Bus 1 Main Bus Line

Either of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 1 is suspected.
• Resistance between CAN bus lines (CANH and CANL) in Bus 1 is below 54 Ω.

Short in Bus 1 Lines

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 1 is suspected.
• Resistance between CANH and +B in Bus 1 is below 6 kΩ.
• Resistance between CANL and +B in Bus 1 is below 6 kΩ.

Short to +B in Bus 1 Line

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 1 is suspected.
• Resistance between CANH and ground in Bus 1 is below 200 Ω.
• Resistance between CANL and ground in Bus 1 is below 200 Ω.

Short to GND in Bus 1 Line

Resistance between CANH and CANL is normal in Bus 1 and the problem symptom pattern in How to Use "Communication Bus Check" Screen in Inspection matches the symptoms when there is an open in one wire of a branch line in Bus 1.

Open in One Side of Bus 1 Branch Line

Either of the following:

• The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 2.
• Resistance between CAN bus lines (CANH and CANL) in Bus 2 is 70 Ω or more.

Open in Bus 2 Main Bus Line

Either of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 2 is suspected.
• Resistance between CAN bus lines (CANH and CANL) in Bus 2 is below 54 Ω.

Short in Bus 2 Lines

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 2 is suspected.
• Resistance between CANH and +B in Bus 2 is below 6 kΩ.
• Resistance between CANL and +B in Bus 2 is below 6 kΩ.

Short to +B in Bus 2 Line

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 2 is suspected.
• Resistance between CANH and ground in Bus 2 is below 200 Ω.
• Resistance between CANL and ground in Bus 2 is below 200 Ω.

Short to GND in Bus 2 Line

Either of the following:

• The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 3.
• Resistance between CAN bus lines (CANH and CANL) in Bus 3 is 70 Ω or more.

Open in Bus 3 Main Bus Line

Either of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 3 is suspected.
• Resistance between CAN bus lines (CANH and CANL) in Bus 3 is below 54 Ω.

Short in Bus 3 Lines

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 3 is suspected.
• Resistance between CANH and +B in Bus 3 is below 6 kΩ.
• Resistance between CANL and +B in Bus 3 is below 6 kΩ.

Short to +B in Bus 3 Line

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 3 is suspected.
• Resistance between CANH and ground in Bus 3 is below 200 Ω.
• Resistance between CANL and ground in Bus 3 is below 200 Ω.

Short to GND in Bus 3 Line

Resistance between CANH and CANL is normal in Bus 3 and the problem symptom pattern in How to Use "Communication Bus Check" Screen in Inspection matches the symptoms when there is an open in one wire of a branch line in Bus 3.

Open in One Side of Bus 3 Branch Line

Either of the following:

• The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 4.
• Resistance between CAN bus lines (CANH and CANL) in Bus 4 is 70 Ω or more.

Open in Bus 4 Main Bus Line

Either of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 4 is suspected.
• Resistance between CAN bus lines (CANH and CANL) in Bus 4 is below 54 Ω.

Short in Bus 4 Lines

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 4 is suspected.
• Resistance between CANH and +B in Bus 4 is below 6 kΩ.
• Resistance between CANL and +B in Bus 4 is below 6 kΩ.

Short to +B in Bus 4 Line

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 4 is suspected.
• Resistance between CANH and ground in Bus 4 is below 200 Ω.
• Resistance between CANL and ground in Bus 4 is below 200 Ω.

Short to GND in Bus 4 Line

Resistance between CANH and CANL is normal in Bus 4 and the problem symptom pattern in How to Use "Communication Bus Check" Screen in Inspection matches the symptoms when there is an open in one wire of a branch line in Bus 4.

Open in One Side of Bus 4 Branch Line

Either of the following:

• The problem symptom is that of Problem Symptom Pattern B and the suspected area is in Bus 5.
• Resistance between CAN bus lines (CANH and CANL) in Bus 5 is 70 Ω or more.

Open in Bus 5 Main Bus Line

Either of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short between CAN bus lines (CANH and CANL) in Bus 5 is suspected.
• Resistance between CAN bus lines (CANH and CANL) in Bus 5 is below 54 Ω.

Short in Bus 5 Lines

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to +B in a CAN bus line (CANH or CANL) in Bus 5 is suspected.
• Resistance between CANH and +B in Bus 5 is below 6 kΩ.
• Resistance between CANL and +B in Bus 5 is below 6 kΩ.

Short to +B in Bus 5 Line

Any of the following:

• The problem symptom is similar to that of Problem Symptom Pattern A and a short to ground in a CAN bus line (CANH or CANL) in Bus 5 is suspected.
• Resistance between CANH and ground in Bus 5 is below 200 Ω.
• Resistance between CANL and ground in Bus 5 is below 200 Ω.

Short to GND in Bus 5 Line

Resistance between CANH and CANL is normal in Bus 5 and the problem symptom pattern in How to Use "Communication Bus Check" Screen in Inspection matches the symptoms when there is an open in one wire of a branch line in Bus 5.

Open in One Side of Bus 5 Branch Line

Either of the following is met:

• Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.)

Skid Control ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Clearance Warning (Intuitive Parking Assist)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Clearance Warning (Intuitive Parking Assist)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Clearance Warning (Intuitive Parking Assist)" is 6 or more.)

Clearance Warning ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Air Conditioning Amplifier" is 6 or more.)

Air Conditioning Amplifier Communication Stop Mode

Either of the following is met:

• Communication stop for "Power Steering (EPS)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Power Steering (EPS)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Power Steering (EPS)" is 6 or more.)

Power Steering ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Spiral cable (Steering Angle Sensor)" is 6 or more.)

Steering Angle Sensor Communication Stop Mode

Either of the following is met:

• Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)

ECM Communication Stop Mode

Either of the following is met:

• Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Main Body" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Main Body" is 6 or more.)

Main Body ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Combination Meter" is 6 or more.)

Combination Meter ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Certification (Smart)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Certification (Smart)" is 6 or more.)

Certification ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Airbag" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Airbag" is 6 or more.)

Center Airbag Sensor Communication Stop Mode

Either of the following is met:

• Communication stop for "Suspension Control (Air Suspension)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Suspension Control (Air Suspension)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Suspension Control (Air Suspension)" is 6 or more.)

Suspension Control ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "HL AutoLeveling/AFS/AHS (Sub)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "HL AutoLeveling/AFS/AHS (Sub)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "HL AutoLeveling/AFS/AHS (Sub)" is 6 or more.)

Headlight ECU RH Communication Stop Mode

Either of the following is met:

• Communication stop for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "HL AutoLeveling/AFS/AHS" is 6 or more.)

Headlight ECU LH Communication Stop Mode

Either of the following is met:

• Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Display and Navigation (AVN)" is 6 or more.)

Radio Receiver Assembly Communication Stop Mode

Either of the following is met:

• Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Blind Spot Monitor Master" is 6 or more.)

Blind Spot Monitor Sensor Communication Stop Mode

Either of the following is met:

• Communication stop for "Active Noise Control" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Active Noise Control" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Active Noise Control" is 6 or more.)

Active Noise Control ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is 6 or more.)

Parking Assist ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Multiplex Tilt and Telescopic" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Multiplex Tilt and Telescopic" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Multiplex Tilt and Telescopic" is 6 or more.)

Tilt and Telescopic ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "DCM" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "DCM" is 6 or more.)

DCM Communication Stop Mode

Either of the following is met:

• Communication stop for "D-Seat" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "D-Seat" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "D-Seat" is 6 or more.)

Driver Seat Control ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is 6 or more.)

Door Mirror ECU LH Communication Stop Mode

Either of the following is met:

• Communication stop for "Front Door RH/R-Mirror (FR-Door/R-Mirror)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Front Door RH/R-Mirror (FR-Door/R-Mirror)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Front Door RH/R-Mirror (FR-Door/R-Mirror)" is 6 or more.)

Door Mirror ECU RH Communication Stop Mode

Either of the following is met:

• Communication stop for "Driving Support (CruiseControl-ACC)" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Driving Support (CruiseControl-ACC)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Driving Support (CruiseControl-ACC)" is 6 or more.)

Driving Support ECU Communication Stop Mode

Either of the following is met:

• Communication stop for "Head Up Display" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Head Up Display" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Head Up Display" is 6 or more.)

Headup Display Communication Stop Mode

Either of the following is met:

• Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Front Radar" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Front Radar" is 6 or more.)

Millimeter Wave Radar Sensor Communication Stop Mode

Either of the following is met:

• Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Parking Assist Monitor System / Rear Camera" is 6 or more.)

Rear Television Camera Communication Stop Mode

Either of the following is met:

• Communication stop for "Occupant Detection" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Occupant Detection" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Occupant Detection" is 6 or more.)

Restraints Occupant Classification System Module Communication Stop Mode

Either of the following is met:

• Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Front Camera Module" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Front Camera Module" is 6 or more.)

Front Camera Module Communication Stop Mode

Either of the following is met:

• Communication stop for "Tire Pressure" is indicated on the "Communication Bus Check" screen of the Techstream.
• Communication stop history for "Tire Pressure" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Tire Pressure" is 6 or more.)

Tire Pressure Monitor ECU Communication Stop Mode

Although CAN communication is currently normal, an ECU connected to the CAN communication system has CAN communication DTCs.

The probable part for which communication is interrupted can be determined using DTC Combination Table and comparing the DTCs output from ECUs connected to the CAN communication system.