Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Check Bus 1 Line for Short to +B

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Power Source, Network / Networking / Can Communication System(for Hv Model) / Check Bus 1 Line for Short to +B

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom

Trouble Area

There is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
  • Short to +B in CAN main bus line
  • Short to +B in CAN branch line
  • Central gateway ECU (network gateway ECU)
  • Forward recognition camera
  • Millimeter wave radar sensor assembly
  • Swing grille actuator assembly
  • Blind spot monitor sensor RH
  • Television camera assembly
  • Clearance warning ECU assembly

    (w/ Intelligent Clearance Sonar System)

  • Parking assist ECU

    (w/ Panoramic View Monitor System)

  • Driving support ECU assembly
  • No. 1 CAN junction connector
  • No. 7 CAN junction connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the A48 No. 1 CAN junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 1 CAN Junction Connector)

*b

to Millimeter Wave Radar Sensor Assembly

*c

to Forward Recognition Camera

*d

to Central Gateway ECU (Network Gateway ECU)

*e

to Swing Grille Actuator Assembly

*f

to No. 7 CAN Junction Connector

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

A48-1 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Millimeter wave radar sensor assembly

A48-7 (CANL) - G45-16 (BAT)

A48-2 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Forward recognition camera

A48-8 (CANL) - G45-16 (BAT)

A48-3 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Central gateway ECU (network gateway ECU)

A48-9 (CANL) - G45-16 (BAT)

A48-4 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Swing grille actuator assembly

A48-10 (CANL) - G45-16 (BAT)

A48-5 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

No. 7 CAN junction connector

A48-11 (CANL) - G45-16 (BAT)

Result

Proceed to

OK

A

NG (Line to central gateway ECU (network gateway ECU))

B

NG (Line to No. 7 CAN junction connector)

C

NG (Line to ECU or sensor)

D
A

REPLACE NO. 1 CAN JUNCTION CONNECTOR
C

GO TO STEP 3

D

GO TO STEP 5

B

2.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect the G52 central gateway ECU (network gateway ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 1 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:

Tester Connection

Condition

Specified Condition

A48-3 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

A48-9 (CANL) - G45-16 (BAT)
OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 7 CAN JUNCTION CONNECTOR)

(a) Disconnect the K66 No. 7 CAN junction connector.

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 7 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

*c

to Clearance Warning ECU Assembly

(w/ Intelligent Clearance Sonar System)

*d

to Blind Spot Monitor Sensor RH

*e

to Television Camera Assembly

*f

to No. 1 CAN Junction Connector

*g

to Parking Assist ECU

(w/ Panoramic View Monitor System)

*h

to Driving Support ECU Assembly

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

K66-1 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Central gateway ECU (network gateway ECU)

K66-11 (CANL) - G45-16 (BAT)

K66-2 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Clearance warning ECU assembly*1

K66-12 (CANL) - G45-16 (BAT)

K66-3 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Blind spot monitor sensor RH

K66-13 (CANL) - G45-16 (BAT)

K66-4 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Television camera assembly

K66-14 (CANL) - G45-16 (BAT)

K66-5 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

No. 1 CAN junction connector

K66-15 (CANL) - G45-16 (BAT)

K66-8 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Parking assist ECU*2

K66-18 (CANL) - G45-16 (BAT)

K66-9 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

Driving support ECU assembly

K66-19 (CANL) - G45-16 (BAT)
  • *1: w/ Intelligent Clearance Sonar System
  • *2: w/ Panoramic View Monitor System

Result

Proceed to

OK

A

NG (Line to central gateway ECU (network gateway ECU))

B

NG (Line to No. 1 CAN junction connector)

C

NG (Line to ECU or sensor)

D
A

REPLACE NO. 7 CAN JUNCTION CONNECTOR
C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
D

GO TO STEP 5

B

4.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect the G52 central gateway ECU (network gateway ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 7 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:

Tester Connection

Condition

Specified Condition

K66-1 (CANH) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

K66-11 (CANL) - G45-16 (BAT)
OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

5.

CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Component with harness connected

(Central Gateway ECU (Network Gateway ECU))

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

G52-23 (CA1H) - G45-16 (BAT)

Cable disconnected from negative (-) auxiliary battery terminal

6 kΩ or higher

G52-8 (CA1L) - G45-16 (BAT)

HINT:

  • If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
  • If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
OK

REPLACE ECU OR SENSOR
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
    Certification ECU Communication Stop Mode

    Check Bus 1 Line for Short to GND

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Toyota Entune System(for Gasoline Model): Confirm Cellular Phone Functionality
    PROCEDURE 1. CHECK CUSTOMER'S CELLULAR PHONE COMPATIBILITY (a) Check if the cellular phone is compatible (Refer to http://www.toyota.com/Entune/). Result Proceed to Cellular phone is compatible. A Cellular phone is not compatible. B HINT: It is important to check the cellular phone compatibility cha ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0218