Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Check Bus 3 Line for Short to +B

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Power Source, Network / Networking / Can Communication System(for Hv Model) / Check Bus 3 Line for Short to +B

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom	Trouble Area
There is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.	Short to +B in CAN main bus line Short to +B in CAN branch line Central gateway ECU (network gateway ECU) Radio and display receiver assembly DCM (telematics transceiver) No. 4 CAN junction connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
Before replacing the DCM (telematics transceiver), refer to Registration.
Click here

HINT:

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.	CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the G95 No. 4 CAN junction connector.

DLC3

Front view of wire harness connector

(to No. 4 CAN Junction Connector)

to Central Gateway ECU (Network Gateway ECU)

to DCM (Telematics Transceiver)

Standard Resistance:

Tester Connection	Condition	Specified Condition	Connected to
G95-9 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher	Central gateway ECU (network gateway ECU)
G95-20 (CANL) - G45-16 (BAT)		6 kΩ or higher	Central gateway ECU (network gateway ECU)
G95-10 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher	DCM (telematics transceiver)
G95-21 (CANL) - G45-16 (BAT)		6 kΩ or higher	DCM (telematics transceiver)
G95-11 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher	Central gateway ECU (network gateway ECU)
G95-22 (CANL) - G45-16 (BAT)		6 kΩ or higher	Central gateway ECU (network gateway ECU)

Result	Proceed to
OK	A
NG (Line to central gateway ECU (network gateway ECU))	B
NG (Line to ECU or sensor)	C

GO TO STEP 3

GO TO STEP 4

2.	CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

(a) Disconnect the G96 No. 4 CAN junction connector.

(b) Measure the resistance according to the value(s) in the table below.

DLC3

Front view of wire harness connector

(to No. 4 CAN Junction Connector)

to Radio and Display Receiver Assembly

Standard Resistance:

Tester Connection	Condition	Specified Condition	Connected to
G96-1 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher	Radio and display receiver assembly
G96-12 (CANL) - G45-16 (BAT)		6 kΩ or higher	Radio and display receiver assembly

REPLACE NO. 4 CAN JUNCTION CONNECTOR

GO TO STEP 4

3.	CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect the G52 central gateway ECU (network gateway ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

DLC3

Front view of wire harness connector

(to No. 4 CAN Junction Connector)

to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:

Tester Connection	Condition	Specified Condition
G95-9 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
G95-20 (CANL) - G45-16 (BAT)		6 kΩ or higher
G95-11 (CANH) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
G95-22 (CANL) - G45-16 (BAT)		6 kΩ or higher

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.	CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click here

DLC3

Component with harness connected

(Central Gateway ECU (Network Gateway ECU))

Standard Resistance:

Tester Connection	Condition	Specified Condition
G52-6 (CA3H) - G45-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
G52-21 (CA3L) - G45-16 (BAT)		6 kΩ or higher

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.

REPLACE ECU OR SENSOR

REPAIR OR REPLACE HARNESS OR CONNECTOR

Check Bus 2 Lines for Short Circuit

Check Bus 3 Line for Short to GND

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Pre-collision System(for Gasoline Model): Operation Check
OPERATION CHECK CHECK PRE-COLLISION SYSTEM SETTING (a) Turn the engine switch on (IG). (b) Operate the steering pad switch assembly to change the setting of PCS on the multi-information display to "On" and check that the pre-collision system turns on. HINT: When the engine switch is turned on (IG), ...

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Check Bus 3 Line for Short to +B

Check Bus 2 Lines for Short Circuit

Check Bus 3 Line for Short to GND

See More:

Toyota Avalon (XX50) 2019-2022 Owners Manual

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual