DESCRIPTION This DTC is
stored when LIN communication between the certification ECU (smart key
ECU assembly) and steering lock ECU (steering lock actuator or upper
bracket assembly) stops for 10 seconds or more. |
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area | |
B2786 | No Response from Steering Lock ECU |
No
communication between steering lock ECU (steering lock actuator or
upper bracket assembly) and certification ECU (smart key ECU assembly)
for 10 seconds or more. |
- Certification ECU (smart key ECU assembly)
- Steering lock ECU (steering lock actuator or upper bracket assembly)
- Wire harness or connector
- STRG LOCK fuse
| WIRING DIAGRAM
 CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly) or
steering lock ECU (steering lock actuator or upper bracket assembly),
refer to Registration.
Click here 
- When using the Techstream with the engine switch off, connect the
Techstream to the DLC3 and turn a courtesy light switch on and off at
intervals of 1.5 seconds or less until communication between the
Techstream and the vehicle begins. Then select Model Code "KEY REGIST"
under manual mode and enter the following menus: Body Electrical / Smart
Key. While using the Techstream, periodically turn a courtesy light
switch on and off at intervals of 1.5 seconds or less to maintain
communication between the Techstream and the vehicle.
PROCEDURE |
1. | CHECK
HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) -
STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)) |
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
G40-13 (LIN) - G43-5 (LIN) |
Always | Below 1 Ω |
| NG |
 | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
OK |
 | |
| 2. |
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - BATTERY AND BODY GROUND) |
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage: |
Tester Connection | Condition |
Specified Condition | |
G43-7 (B) - G43-1 (GND) |
Always | 11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
G43-1 (GND) - Body ground |
Always | Below 1 Ω |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
OK | |
| |
| 3. |
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
(a) Replace the steering lock ECU (steering lock actuator or upper bracket assembly).
for Manual Tilt and Manual Telescopic Steering Column: Click here
for Power Tilt and Power Telescopic Steering Column: Click here
|
NEXT | |
| |
| 4. |
REGISTER ECU CODE REGISTRATION | (a) Register the recognition codes in the ECUs.
HINT: Refer to Registration. Click here
|
NEXT | |
| |
(a) Clear the DTCs. Body Electrical > Smart Key > Clear DTCs
(b) Recheck for DTCs. Body Electrical > Smart Key > Trouble Codes
OK: DTC B2786 is not output.
| OK |
| END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE) |
| NG |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) | | 
