CAUTION / NOTICE / HINT HINT: Perform this troubleshooting procedure when no DTCs are output, including DTCs related to CAN communication system malfunctions. PROCEDURE
| 1. |
READ VALUE USING TECHSTREAM (ASSIST LIMIT RECORD 1) |
(a) Using the Techstream, read the Data List item "Assist Limit Record 1".
Click here  Chassis > EMPS > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Assist Limit Record 1 | Information of assist limit that was used in the past or is currently in use (latest history) |
Unrec,
Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF,
Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep |
- | - |
HINT: For the Data List item "Assist Limit Record 1", each item in the Range is described below. | |
Range | Description |
Diagnostic Note | |
Assist Limit Record 1 | Unrec |
No assist limit. Continue with troubleshooting for "Heavy steering". |
- | | Mtr Overheat |
When
the vehicle is stopped or traveling at low speed, and steering
operations are performed repeatedly or the steering wheel is turned all
the way to the side and held there for a long time, assist may be
limited in order to prevent overheating of the power steering motor
assembly and power steering ECU assembly. After 10 minutes elapse with the engine running and no steering operations being performed, the system will return to normal.
After recovering from the overheated condition, assist can be performed as usual. |
- | | Pow Vol Low |
When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be stopped.
After the battery condition returns to normal, assist can be performed as usual. |
- | | Pow Vol Low Prevent |
When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual. |
- | | Eng Stall |
When the engine stalls, battery charge becomes insufficient, so assist is stopped.
After recovering from the engine stall, assist can be performed as usual. |
- | | Ready OFF |
After
Ready ON, if a malfunction in the HV system etc. causes a return to
Ready OFF, the HV battery charge becomes insufficient, so assist is
stopped. After returning to Ready ON state, assist can be performed as usual. |
Not displayed for this vehicle | |
Mtr Overload | When
the steering wheel cannot turn, such as when a road wheel is against a
curb, if the driver continues to apply force to the steering wheel,
current to the motor may be limited to prevent overheating. When the steering wheel is returned to a neutral position, assist can be performed as usual. |
- | | DC-DC Malf |
If there is a malfunction in the DC-DC converter, etc., assist may be limited.
After the DC-DC converter returns to normal, assist can be performed as usual. |
Not displayed for this vehicle | |
Vhcl Spd Sig Malf | If the vehicle speed signal is abnormal due to a wheel speed sensor malfunction, etc., assist may be limited. |
- | | Batt Vol Keep |
When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual. |
- | Chassis > EMPS > Data List
|
Tester Display | | Assist Limit Record 1 |
(b)
Based on the "Assist Limit Record 1" information, the following Data
List items and the information from the customer interview, explain the
situation to the customer. Chassis > EMPS > Data List
|
Tester Display | | Record 1 Key Cycle | |
Record 1 Key Cycle Elapsed Time | HINT:
If
it is necessary to investigate further into the past, check the "Assist
Limit Record 2" and "Assist Limit Record 3" information in the same way
as "Assist Limit Record 1".
| NEXT |  |
END | |
