DESCRIPTION Different
voltage values are sent to the multiplex tilt and telescopic ECU by
operating the tilt and telescopic switch. The multiplex tilt and
telescopic ECU then judges which motor and in which direction that motor
should operate based on the voltage value. WIRING DIAGRAM
 PROCEDURE
| 1. |
READ VALUE USING TECHSTREAM (TILT MANUAL SWITCH UP/DOWN, TELESCOPIC MANUAL SWITCH SHORT/LONG) |
(a) Turn the power switch off. (b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG). (d) Turn the Techstream on. (e) Read the Data List according to the display on the Techstream. Body Electrical > Tilt&Telescopic > Data List
|
Tester Display | | Tilt Manual Switch Up | |
Tilt Manual Switch Down | |
Telescopic Manual Switch Short | |
Telescopic Manual Switch Long | Body Electrical > Tilt&Telescopic > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Tilt Manual Switch Up | Input state of tilt up switch |
OFF or ON | - |
- | | Tilt Manual Switch Down |
Input state of tilt down switch |
OFF or ON | - |
- | | Telescopic Manual Switch Short |
Input state of telescopic contract switch |
OFF or ON | - |
- | | Telescopic Manual Switch Long |
Input state of telescopic extend switch |
OFF or ON | - |
- | OK: The value of each Data List item changes in accordance with the operation of the switch.
| OK |
 | REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
|
NG |
 | |
| 2. |
CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH) |
(a) Disconnect the G49 multiplex tilt and telescopic ECU connector. (b) Disconnect the G30 tilt and telescopic switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
G49-5 (VC) - G30-1 (VC) |
Always | Below 1 Ω | |
G49-18 (MSW) - G30-3 (MSW) |
Always | Below 1 Ω | |
G49-5 (VC) or G30-1 (VC) - Body ground |
Always | 10 kΩ or higher | |
G49-18 (MSW) or G30-3 (MSW) - Body ground |
Always | 10 kΩ or higher |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
OK | |
| |
| 3. |
CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE) |
| (a) Reconnect the G49 multiplex tilt and telescopic ECU connector. |
 |
|
*a | Component with harness connected
(Multiplex Tilt and Telescopic ECU) | | |
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage: |
Tester Connection | Condition |
Specified Condition | |
G49-5 (VC) - G49-18 (MSW) |
Power switch on (IG) |
4.9 to 5.1 V |
| NG |
| REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
|
OK | |
| |
| 4. |
CHECK TILT AND TELESCOPIC SWITCH |
| (a) Remove the tilt and telescopic switch. Click here
 |
 |
|
*a | Component without harness connected
(Tilt and Telescopic Switch) | | |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
G30-1 (VC) - G30-3 (MSW) |
Tilt up | 342 to 378 Ω | |
Tilt down | 1890.5 to 2089.5 Ω | |
Telescopic contract | 750.5 to 829.5 Ω | |
Telescopic extend | 152 to 168 Ω |
| OK |
| REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
| NG |
| REPLACE TILT AND TELESCOPIC SWITCH | | 
