Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Terminals Of Ecu

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Suspension / Tire Pressure Monitoring / Tire Pressure Warning System(for Hv Model) / Terminals Of Ecu

TERMINALS OF ECU

CHECK TIRE PRESSURE WARNING ECU AND RECEIVER

(a) Disconnect the K11 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

*a

Front view of wire harness connector

(to Tire Pressure Warning ECU and Receiver)

Terminal No. (Symbol)

Wiring Color

Terminal Description

Condition

Specified Condition

K11-1 (IG) - K11-12 (GND)

B - BR

IG power source

Power switch on (IG)

10 to 16 V

K11-7 (+B) - K11-12 (GND)

LA-R - BR

Power supply (from auxiliary battery)

Always

10 to 16 V

K11-9 (CANH) - K11-10 (CANL)

L - W

CAN communication line

Power switch off

54 to 69 Ω

K11-12 (GND) - Body ground

BR - Body ground

Ground

Always

Below 1 Ω

(b) Connect the K11 tire pressure warning ECU and receiver connector.

(c) Measure the voltage according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.

*a

Component with harness connected

(Tire Pressure Warning ECU and Receiver)

-

-

Terminal No. (Symbol)

Wiring Color

Terminal Description

Condition

Specified Condition

K11-3 (CLSW) - K11-12 (GND)

SB - BR

Tire pressure warning reset switch
  • Power switch on (IG)
  • Steering pad switch assembly operated, "Set Pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held

Below 1.5 V
  • Power switch on (IG)
  • "OK" switch (steering pad switch assembly) off

8 to 15 V

K11-4 (RDA) - K11-12 (GND)

GR - BR

Output signals

Power switch on (IG)

Pulse generation (see waveform 1)

K11-5 (PRG) - K11-12 (GND)

R - BR

Input signals

Power switch on (IG)

Pulse generation (see waveform 1)

(d) Using an oscilloscope, check waveform 1.

*a

Example

*b

GND
Waveform 1:

Item

Contents

Terminal

K11-4 (RDA) - K11-12 (GND)

K11-5 (PRG) - K11-12 (GND)

Tool setting

5 V/DIV, 5 ms./DIV.

Vehicle condition

Power switch on (IG)

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.

    System Diagram

    Test Mode Procedure

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Active Noise Control Microphone: Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during active noise control microphone removal/installation are shown below. Necessary Procedure After Parts R ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2025 Copyright www.tavalon.net
    0.015