Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) for Main Body: Body Electrical / Main Body / Data List.

(2) for HL AutoLeveling: Body Electrical / HL AutoLeveling / Data List.

(3) for HL AutoLeveling (Sub): Body Electrical / HL AutoLeveling (Sub) / Data List.

(4) for Steering Angle Sensor: Chassis / Steering Angle Sensor / Data List.

(5) for Combination Meter: Body Electrical / Combination Meter / Data List.

(6) for Front Recognition Camera: Chassis / Front Recognition Camera / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Auto High Beam Main Switch

Auto high beam switch signal

OFF or ON

OFF: Auto high beam switch not pressed

ON: Auto high beam switch pressed

-

Head Light SW (Head)

Light control switch head position signal

OFF or ON

OFF: Light control switch not in head position

ON: Light control switch in head position

-

Insolation Amount of Solar Sensor RH

Solar sensor RH condition

0 to 51100 or SensorFail

Condition can be displayed

-

Insolation Amount of Solar Sensor LH

Solar sensor LH condition

0 to 51100 or SensorFail

Condition can be displayed

-

Light Sensor Illuminance

Light control sensor illuminance

0 to 8191 lx or SensorFail

Value is output according to ambient light level

-

Light Sensor Connection Status

Light control sensor connection status

OFF or ON

OFF: Automatic light control sensor has not been connected

ON: Automatic light control sensor connected or has been connected

-

Headlight Lighting Function

ECU which controls the lighting system

Main Body or Lighting Sys ECU

Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)

Lighting Sys ECU: Lighting system is controlled by headlight ECU sub-assembly

-

Sensitivity

Sensitivity of the automatic light control system

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

DRL Function

Setting of the DRL function on/off

OFF or ON

Customize setting displayed

for vehicles with customize setting "DRL Function"

Headlight in Conjunction with Wiper

Wiper-linked low beam headlight control

OFF or ON

Customize setting displayed

-

Disp Ex ON Sen

Ambient brightness level required to dim display lights (combination meter, navigation display, etc.)

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

Disp Ex OFF Sen

Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.)

Light2, Light1, Normal, Dark1 or Dark2

Customize setting displayed

-

Light Auto OFF Delay

Light auto OFF delay

Off, 30 s, 60 s or 90 s

Customize setting displayed

-

Auto H Beam STS0

Automatic high beam sensor current state

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning.

Auto H Beam STS1

Automatic high beam sensor state past 1

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS2

Automatic high beam sensor state past 2

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS3

Automatic high beam sensor state past 3

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS4

Automatic high beam sensor state past 4

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS5

Automatic high beam sensor state past 5

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS6

Automatic high beam sensor state past 6

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Auto H Beam STS7

Automatic high beam sensor state past 7

Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err

Condition can be displayed*

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Light up Clearance Lights at Door Unlock Function

Setting of the welcome light illumination control customize setting

OFF or ON

Customize setting displayed

-

Tail Remind Buzzer Function

Setting of the tail remind buzzer function on/off

OFF or ON

Customize setting displayed

-

The Number of DTC

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

HINT:

*: The details of each value of the Range are as follows:

Display Value

Condition

Control Condition

Diagnostic Note

Undetec

Automatic high beam sensor being initialized

Control suspended (low beam headlights illuminated)

-

CAM NA

Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc.

Control suspended (low beam headlights illuminated)

-

No sens

No lights detected

High beam headlights illuminated

Only when vehicle speed within operation speed range

Hlight

Headlights of oncoming vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Taillgt

Taillights preceding vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Speed

No lights detected and vehicle speed below operation speed

Low beam headlights illuminated

-

Daytime

Bright light detected

Low beam headlights illuminated

-

Village

Streetlights, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Delay

Changing between low beams and high beams

Changing between low beams and high beams

Only when vehicle speed within operation speed range

SAE Mod

Not applicable

-

-

Malfunc

Aim Lmt

Undefin

LIN Err

Body Electrical > HL AutoLeveling > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Headlight Low Beam State

Low beam headlight state

OFF or ON

OFF: Low beam headlights off

ON: Low beam headlights on

-

Headlight High Beam State

High beam headlight state

OFF or ON

OFF: High beam headlights off

ON: High beam headlights on

-

+B

Headlight ECU sub-assembly LH IG power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Front Right Wheel Speed Value

Front right wheel speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Front Left Wheel Speed Value

Front left wheel speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Vehicle Speed

Vehicle speed

0.00 to 260.00 km/h (162.00 mph)

Condition can be displayed

-

Steering Sensor Signal

Steering sensor signal value

-384.0 to 382.5 deg

Changes according to the operation of the steering wheel

Turning left: Increases

Turning right: Decreases

Steering Sensor Center Position

Steering sensor center position

-3072.0 to 3070.5 deg

0.0 deg (tires straight ahead)

-

+B Voltage Value

Headlight ECU sub-assembly LH +B power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Leveling Motor Target Position

Headlight leveling motor target position

0.0 to 102.3 %

10.0 to 90.0 %

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Steering Sensor Initialization Status

Steering sensor initialization state

Incomplete or Completed

Incomplete: Steering sensor zero point calibration incomplete

Completed: Steering sensor zero point calibration complete

-

Clearance Light State

Parking light state

OFF or ON

OFF: Parking lights off

ON: Parking lights on

-

Right Cornering Light/Front Side Illuminate Light State

Cornering light RH/front side illumination light RH state

OFF or ON

OFF: Cornering light RH/front side illumination light RH off

ON: Cornering light RH/front side illumination light RH on

-

Left Cornering Light/Front Side Illuminate Light State

Cornering light LH/front side illumination light LH state

OFF or ON

OFF: Cornering light LH/front side illumination light LH off

ON: Cornering light LH/front side illumination light LH on

-

DRL Operating State

Daytime running light state

OFF or ON

OFF: Daytime running lights off

ON: Daytime running lights on

-

Number Of Trouble Codes

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Body Electrical > HL AutoLeveling (Sub) > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Front Window Washer Switch

Windshield wiper switch assembly (washer switch) condition

OFF or ON

OFF: Windshield wiper switch assembly (washer switch) off

ON: Windshield wiper switch assembly (washer switch) on

-

Headlight Cleaner Switch

Headlight cleaner switch condition

OFF or ON

OFF: Headlight cleaner switch off

ON: Headlight cleaner switch on

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Headlight Low Beam State

Low beam headlight state

OFF or ON

OFF: Low beam headlights off

ON: Low beam headlights on

-

Headlight High Beam State

High beam headlight state

OFF or ON

OFF: High beam headlights off

ON: High beam headlights on

-

Clearance Light State

Parking light state

OFF or ON

OFF: Parking lights off

ON: Parking lights on

-

DRL State(DRL Operating State)

Daytime running light state

OFF or ON

OFF: Daytime running lights off

ON: Daytime running lights on

-

+B

Headlight ECU sub-assembly RH IG power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

+B Voltage Value

Headlight ECU sub-assembly RH +B power supply voltage value

0.00 to 19.75 V

11.00 to 14.00 V

-

Number Of Trouble Codes

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Light OFF Switch

Light control switch DRL OFF position signal

OFF or ON

OFF: Light control switch not in DRL OFF position

ON: Light control switch in DRL OFF position

w/ DRL OFF Switch

Auto Light Switch

Light control switch AUTO position signal

OFF or ON

OFF: Light control switch not in AUTO position

ON: Light control switch in AUTO position

-

Head Light Switch (Tail)

Light control switch tail position signal

OFF or ON

OFF: Light control switch in neither tail nor head position

ON: Light control switch in tail or head position

-

Head Light Switch (Head)

Light control switch head position signal

OFF or ON

OFF: Light control switch not in head position

ON: Light control switch in head position

-

High Beam Main Switch

Dimmer switch high position signal

OFF or ON

OFF: Dimmer switch not in high position

ON: Dimmer switch in high position

-

Passing Light Switch

Dimmer switch high flash position (pass) signal

OFF or ON

OFF: Dimmer switch not in high flash position

ON: Dimmer switch in high flash position

-

Auto High Beam Main Switch

Auto high beam switch signal

OFF or ON

OFF: Auto high beam switch off

ON: Auto high beam switch on

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Turn Signal Switch (Right)

Turn signal switch (right turn position) signal

OFF or ON

OFF: Turn signal switch not in right turn position

ON: Turn signal switch in right turn position

-

Turn Signal Switch (Left)

Turn signal switch (left turn position) signal

OFF or ON

OFF: Turn signal switch not in left turn position

ON: Turn signal switch in left turn position

-

Cornering Light/Front Side Illuminate Light Switch

Turn signal switch (full turn) signal

OFF or ON

OFF: Turn signal switch not in left or right turn position

ON: Turn signal switch in left or right full turn position

-

Front Fog Light Switch

Front fog light switch signal

OFF or ON

OFF: Front fog light switch off

ON: Front fog light switch on

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Rear Fog Light/Bad Weather Switch

Rear fog light switch signal

OFF or ON

OFF: Rear fog light switch off

ON: Rear fog light switch on

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Automatic Light Equipped Info

Automatic light control system specification information

Unknown, With or Without

Unknown: Specification not stored

With: Automatic light control system equipped

Without: Automatic light control system not equipped

-

Bad Weather Mode Equipped Info

Bad weather specification information

Unknown, Without or With

Unknown: Specification not stored

Without: Bad weather specification not equipped

With: Bad weather specification equipped

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

The Number of DTCs

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Turn Signal Switch (Left)

Turn signal switch (left) signal

OFF or ON

OFF: Turn signal switch not in left turn position

ON: Turn signal switch in left turn position

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Turn Signal Switch (Right)

Turn signal switch (right) signal

OFF or ON

OFF: Turn signal switch not in right turn position

ON: Turn signal switch in right turn position

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Turn Switch Signal (Full Turn)

Turn signal switch (full turn) signal

OFF or ON

OFF: Turn signal switch not in left or right turn position

ON: Turn signal switch in left or right turn position

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Hazard Flasher Switch

Hazard warning signal switch signal

OFF or ON

OFF: Hazard warning signal switch off

ON: Hazard warning signal switch on

-

Lane Change Flashing Times Adjust

Condition of the lane change flashing times

OFF, 3, 4, 5, 6 or 7

Customize setting displayed

-

Chassis > Front Recognition Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

High Temperature Status1

High temperature malfunction status

OFF or ON

OFF: Forward recognition camera high temperature malfunction does not exist

ON: Forward recognition camera high temperature malfunction exists

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) for Main Body: Body Electrical / Main Body / Active Test.

(2) for HL AutoLeveling: Body Electrical / HL AutoLeveling / Active Test.

(3) for HL AutoLeveling (Sub): Body Electrical / HL AutoLeveling (Sub) / Active Test.

(4) for Combination Meter: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Daytime Running Light

Daytime running lights

OFF or ON

-

Taillight Relay

Taillight relay

OFF or ON

-

Headlight Relay

Low beam headlights

OFF or ON

-

Head Light Hi

High beam headlights

OFF or ON

-

Rear Fog Light Relay

Rear fog lights

OFF or ON

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Automatic High Beam Switch Light

Auto high beam switch indicator light

OFF or ON

-

Body Electrical > HL AutoLeveling > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Drive The Leveling Motor

Headlight leveling motor upward or downward operation

Stop, Down or Up

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Headlight Leveling Indicator

"Headlight System Malfunction Visit Your Dealer" display

OFF or ON

-

Clearance Light

Parking lights

OFF or ON

-

Headlight Low Beam

Low beam headlights

OFF or ON

-

Headlight High Beam

High beam headlights

OFF or ON

-

Daytime Running Light

Daytime running lights

OFF or ON

-

Cornering Light/Front Side Illuminate Light

Cornering light/front side illuminate light

OFF or ON

-

Body Electrical > HL AutoLeveling (Sub) > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Headlight Cleaner

Operate headlight cleaner motor and pump assembly

OFF or ON

Although this item is displayed on the Techstream, it is not applicable to this vehicle.

Clearance Light

Parking lights

OFF or ON

-

Headlight Low Beam

Low beam headlights

OFF or ON

-

Headlight High Beam

High beam headlights

OFF or ON

-

Daytime Running Light

Daytime running lights

OFF or ON

-

Cornering Light/Front Side Illuminate Light

Cornering light/front side illumination light

OFF or ON

-

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Multi Display All (White)

Multi-information display (White display)

OFF or ON

-

    Customize Parameters

    Diagnostic Trouble Code Chart

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Parking Assist Monitor System(for Gasoline Model): Problem Symptoms Table
    PROBLEM SYMPTOMS TABLE NOTICE: The following inspection procedures for the parking assist monitor system are based on the assumption that the audio and visual system*1 or navigation system*2 is normal. If the audio and visual system*1 or navigation system*2 has any malfunctions, first proceed with t ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.014