REMOVAL CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization or
registration) that must be performed after parts are removed and
installed, or replaced during blower unit removal/installation are shown
below. Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link | |
*: When performing learning using the Techstream.
Click here  | |
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
| |
Pre-collision System | |
Intelligent Clearance Sonar System* | |
Lighting System (for Gasoline Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking Assist Monitor System |
| |
Panoramic View Monitor System |
| |
Steering sensor | Steering angle zero point learning (Initialize intelligent clearance sonar system) |
- Intelligent Clearance Sonar System
- Intuitive Parking Assist System
|
|
- Steering angle neutral point (Initialize parking assist monitor system)
- Steering angle setting
| Parking Assist Monitor System |
for Initialization
for Calibration | |
Steering angle zero point learning (Initialize panoramic view monitor system) |
Panoramic View Monitor System |
for Initialization
for Calibration | |
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
| CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
 Click here
HINT: Before removing the blower assembly, set the air conditioning to recirculation mode. Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link | |
*: When performing learning using the Techstream.
Click here | |
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
| |
Pre-collision System | |
Intelligent Clearance Sonar System* | |
Lighting System (for HV Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking Assist Monitor System |
| |
Panoramic View Monitor System |
| |
Steering sensor | Steering angle zero point learning (Initialize intelligent clearance sonar system) |
- Intelligent Clearance Sonar System
- Intuitive Parking Assist System
|
|
- Steering angle zero point learning (Initialize parking assist monitor system)
- Steering angle setting
| Parking Assist Monitor System |
for Initialization
for Calibration | |
Steering angle zero point learning (Initialize panoramic view monitor system) |
Panoramic View Monitor System |
for Initialization
for Calibration | |
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
| CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
HINT: Before removing the blower assembly, set the air conditioning to recirculation mode. PROCEDURE
1. REMOVE AIR CONDITIONER UNIT ASSEMBLY for A25A-FXS: Click here
for 2GR-FKS: Click here
2. REMOVE NO. 2 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Click here 3. REMOVE NO. 2 AIR DUCT
Click here 4. REMOVE BLOWER ASSEMBLY
| (a) Disconnect the connector. | |
(b) Disengage each guide.
(d) Disengage the 2 claws and 2 guides and remove the blower assembly from the air conditioning radiator assembly. | 
