Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Front Radar Sensor Region Code Mismatch (C1A0A)

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Interior / Pre-collision / Pre-collision System(for Gasoline Model) / Front Radar Sensor Region Code Mismatch (C1A0A)

DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.

Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly calculates the possibility of a collision and operates the pre-collision system if it determines that the possibility is high.

When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). If country specification information in the millimeter wave radar sensor assembly, driving support ECU and/or main body ECU do not match, DTC C1A0A will be stored.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1A0A	Front Radar Sensor Region Code Mismatch	When the engine switch is on (IG), the country specification information in the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds.	Millimeter wave radar sensor assembly Driving support ECU assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE

1.	CHECK FOR DTCs

(a) Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

Body Electrical > Pre-Collision 2 > Trouble Codes

Result	Proceed to
DTC C1A0A is not output	A
DTC C1A0A is output	B

USE SIMULATION METHOD TO CHECK

2.	REPLACE DRIVING SUPPORT ECU ASSEMBLY

(a) Replace the driving support ECU assembly.

Click here

3.	CHECK FOR DTCs

(a) Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

Body Electrical > Pre-Collision 2 > Trouble Codes

Result	Proceed to
DTC C1A0A is not output	A
DTC C1A0A is output	B

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

4.	REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

(a) Replace the millimeter wave radar sensor assembly.

Click here

(b) Adjust the millimeter wave radar sensor assembly.

Click here

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

Pre-collision System(for Gasoline Model)

Driving Support ECU (C1A01)

See More:

Toyota Avalon (XX50) 2019-2022 Owners Manual > Before driving: Cargo and luggage
Take notice of the following information about storage precautions, cargo capacity and load: Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit - (1) L ...