DESCRIPTION When a door is
unlocked using the wireless unlock function, the certification ECU
(smart key ECU assembly) sends a key ID signal to the main body ECU
(multiplex network body ECU). When a door is unlocked using the entry
unlock function, the certification ECU (smart key ECU assembly) sends a
door unlock signal and key ID signal to the main body ECU (multiplex
network body ECU). When the main body ECU (multiplex network body ECU)
receives the door unlock signal, it stores the key ID. When the driver
door is opened, the memory call information of the stored key ID is sent
to each driving position related control ECU. Each control ECU receives
the information and then performs the memory call operation according
to predetermined control timing values. CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE |
1. | CHECK FRONT POWER SEAT OPERATION |
(a) Check the operation of the power seat. Click here
 (b) Check the seat position memory function.
Click here (c) Check the seat position restoration function.
Click here (d) Check the operation of memory registration of the memory call function.
Click here
|
Result | Proceed to | |
OK | A | |
NG (Power seat operation) |
B | | NG (Seat position memory function) |
C | | NG (Seat position restoration function) |
D | | NG (Memory registration) |
E |
| B |
 | GO TO PROBLEM SYMPTOMS TABLE |
| C |
| GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized) |
| D |
| GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position) |
| E |
| GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate) |
|
A |
 | |
| 2. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here
|
Result | Proceed to | |
Memory call function linked with the wireless unlock function does not operate. |
A | | Memory call function linked with the entry unlock function does not operate. |
B | | Memory call function linked with the wireless unlock function and entry unlock function both do not operate. |
C |
| B |
| GO TO STEP 9 |
| C |
| GO TO STEP 15 |
|
A | |
| |
| 3. |
CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
(a) Check the wireless unlock function of the wireless door lock control system.
Click here OK: Wireless unlock function is normal.
| NG |
| GO TO WIRELESS DOOR LOCK CONTROL SYSTEM |
|
OK | |
| |
| 4. |
CHECK MEMORY CALL FUNCTION (MIRROR OPERATION) |
(a) Check the operation of the outer mirrors using the memory call function.
Click here
|
Result | Proceed to | |
Outer mirrors operate normally |
A | | Outer mirrors do not operate normally |
B |
| B |
| GO TO STEP 7 |
|
A | |
| |
| 5. |
REPLACE POSITION CONTROL ECU ASSEMBLY |
(a) Replace the position control ECU assembly with a new or known good one.
Click here
|
NEXT | |
| |
| 6. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call function linked with the wireless unlock function operates normally.
| OK |
| END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE) |
| NG |
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| 7. |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
|
NEXT | |
| |
| 8. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call function linked with the wireless unlock function operates normally.
| OK |
| END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| 9. |
CHECK SMART KEY SYSTEM (for Entry Function) |
(a) Check the entry unlock function of the smart key system (for entry function).
Click here OK: Entry unlock function is normal.
| NG |
| GO TO SMART KEY SYSTEM (for Entry Function) |
|
OK | |
| |
| 10. |
CHECK MEMORY CALL FUNCTION (MIRROR OPERATION) |
(a) Check the operation of the outer mirrors using the memory call function.
Click here
|
Result | Proceed to | |
Outer mirrors operate normally |
A | | Outer mirrors do not operate normally |
B |
| B |
| GO TO STEP 13 |
|
A | |
| |
| 11. |
REPLACE POSITION CONTROL ECU ASSEMBLY |
(a) Replace the position control ECU assembly with a new or known good one.
Click here
|
NEXT | |
| |
| 12. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call function linked with the entry unlock function operates normally.
| OK |
| END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE) |
| NG |
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| 13. |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
|
NEXT | |
| |
| 14. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call function linked with the entry unlock function operates normally.
| OK |
| END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG |
| REPLACE CERTIFICATION (SMART KEY ECU ASSEMBLY) |
| 15. |
CHECK MEMORY CALL FUNCTION (MIRROR OPERATION) |
(a) Check the operation of the outer mirrors using the memory call function.
Click here
|
Result | Proceed to | |
Outer mirrors operate normally |
A | | Outer mirrors do not operate normally |
B |
| B |
| GO TO STEP 18 |
|
A | |
| |
| 16. |
REPLACE POSITION CONTROL ECU ASSEMBLY |
(a) Replace the position control ECU assembly with a new or known good one.
Click here
|
NEXT | |
| |
| 17. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call function linked with the wireless unlock and entry unlock function operate normally.
| OK |
| END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE) |
| NG |
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| 18. |
READ VALUE USING TECHSTREAM (MEMORY CALL REGISTRATION) |
(a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG).
(c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream. Body Electrical > Main Body > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Mem SW No. w/KeyID1 | Memory switch linked with key ID1 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* |
- | | Mem SW No. w/KeyID2 |
Memory switch linked with key ID2 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* |
- | | Mem SW No. w/KeyID3 |
Memory switch linked with key ID3 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* |
- | | Mem SW No. w/KeyID4 |
Memory switch linked with key ID4 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* |
- | | Mem SW No. w/KeyID5 |
Memory switch linked with key ID5 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* |
- | | Mem SW No. w/KeyID6 |
Memory switch linked with key ID6 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* |
- | | Mem SW No. w/KeyID7 |
Memory switch linked with key ID7 |
NONE, MEM SW1, MEM SW2 or MEM SW3* |
NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* |
- |
- *: Although this item is displayed on the Techstream, it is not applicable to this vehicle.
Body Electrical > Main Body > Data List
|
Tester Display | | Mem SW No. w/KeyID1 | |
Mem SW No. w/KeyID2 | |
Mem SW No. w/KeyID3 | |
Mem SW No. w/KeyID4 | |
Mem SW No. w/KeyID5 | |
Mem SW No. w/KeyID6 | |
Mem SW No. w/KeyID7 | (f) Enter the following menus: Body Electrical / Driver Seat / Data List.
(g) Read the Data List according to the display on the Techstream. Body Electrical > Driver Seat > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Seat Memory No1 | Seat position memorized with M1 switch |
Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- | | Seat Memory No2 |
Seat position memorized with M2 switch |
Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- | Body Electrical > Driver Seat > Data List
|
Tester Display | | Seat Memory No1 | |
Seat Memory No2 | OK: A
seat position has been memorized for the seat position memory switch
linked to the electrical key transmitter sub-assembly. (For example, the
value of "Mem SW No. w/KeyID1" is MEM SW1 and the value of "Seat Memory
No1" is Mem.) | NG |
| PERFORM MEMORY CALL REGISTRATION |
|
OK | |
| |
| 19. |
READ VALUE USING TECHSTREAM (DRIVER DOOR COURTESY SWITCH) |
(a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG).
(c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream. Body Electrical > Main Body > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
FL Door Courtesy SW | Front door courtesy light switch assembly (driver door) signal |
ON or OFF | ON: Driver door open
OFF: Driver door closed |
- | Body Electrical > Main Body > Data List
|
Tester Display | | FL Door Courtesy SW |
OK: On the Techstream screen, ON or OFF is displayed accordingly.
| NG |
| GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit) |
|
OK | |
| |
| 20. |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
|
NEXT | |
| |
| 21. |
CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION) |
(a) Check the memory registration and automatic memory call function of the memory call function.
Click here OK: Memory call functions linked with the wireless unlock function and entry unlock function operate normally.
| OK |
| END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) | | 
