REMOVAL CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during lumbar support adjuster assembly
removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link | |
*: When performing learning using the Techstream.
Click here  | |
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
| |
Pre-collision system | |
Intelligent clearance sonar system* | |
Lighting system (for Gasoline Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking assist monitor system |
| |
Panoramic view monitor system |
|
- Occupant detection ECU
- Front passenger seat
| Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
- Separate type front seat cushion spring assembly LH
- Front seatback frame sub-assembly LH
- Position control ECU assembly
| Initialize position control ECU |
Front power seat control system |
| Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link | |
*: When performing learning using the Techstream.
Click here | |
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
| |
Pre-collision system | |
Intelligent clearance sonar system* | |
Lighting system (for HV Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking assist monitor system |
| |
Panoramic view monitor system |
|
- Occupant detection ECU
- Front passenger seat
| Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
- Separate type front seat cushion spring assembly LH
- Front seatback frame sub-assembly LH
- Position control ECU assembly
| Initialize position control ECU |
Front power seat control system |
|
CAUTION:
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE 1. REMOVE FRONT SEAT ASSEMBLY
Click here 2. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER
Click here 3. REMOVE FRONT SEAT FRONT CUSHION SHIELD
Click here 4. REMOVE FRONT SEAT CUSHION SHIELD
Click here 5. REMOVE FRONT SEAT INNER CUSHION SHIELD
Click here 6. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here 7. REMOVE FRONT SEAT HEADREST SUPPORT
Click here 8. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Click here 9. REMOVE SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)
Click here 10. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY
(a) w/o Climate Control Seat System:
| (1) Disengage the clamp and disconnect the connector. HINT:
Disengage the clamp first. | |
| (2) Disengage the 8 hooks to remove the lumbar support adjuster assembly. |
|
(b) w/ Climate Control Seat System:
| (1) Disengage the 3 clamps and disconnect the 2 connectors. HINT:
Disengage the 3 clamps first. | |
| (2) Disengage the 2 claws. | |
(3) Disengage the 2 guides to remove the lumbar support adjuster assembly as shown in the illustration.
 |
Remove in this Direction | 11. REMOVE FRONT NO. 2 SEATBACK HOOK (w/ Climate Control Seat System)
Click here | 
