CUSTOMIZE PARAMETERS CUSTOMIZE INTELLIGENT CLEARANCE SONAR SYSTEM
(a) Customizing with the Techstream.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Connect the Techstream to the DLC3. (2) Turn the engine switch on (IG).
(3) Turn the Techstream on. (4) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.
(5) Select the setting by referring to the table below. Warning
|
Tester Display | Description |
Default | Setting |
ECU | | Fr Corner Sensor Onset Range |
Sets the detection operation range for the front corner sensors. |
Long | 0:Short,1:Long |
Clearance warning ECU assembly | |
Rr Corner Sensor Onset Range |
Sets the detection operation range for the rear corner sensors. |
Long | 0:Short,1:Long |
Clearance warning ECU assembly | |
Fr Sensor Onset Range | Sets the detection operation range for the front center sensors. |
Wide | 0:Narrow,1:Wide |
Clearance warning ECU assembly | |
Rr Sensor Onset Range | Sets the detection operation range for the rear center sensors. |
Wide | 0:Narrow,1:Wide |
Clearance warning ECU assembly | |
Keep Sense Buzzer | Sets
whether the buzzer stops sounding when the distance between the vehicle
and a detected object does not change for 3 seconds. |
Avail | 0:Not Avail,1:Avail |
Clearance warning ECU assembly | |
Fr & Rr Buzzer Volume |
Changes the buzzer volume setting. |
M2 | 001:L,010:M1,011:M2,100:M3,101:H |
Clearance warning ECU assembly | |
Object Not Moving 3s Buzz Vol |
Sets
the volume at which the buzzer sounds when the distance between the
vehicle and a detected object does not change for 3 seconds. |
Keep | 00:Keep Vol,01:L,10:M1,11:M2 |
Clearance warning ECU assembly | |
Leave Buzzer Volume | Sets the volume of the buzzer with respect to the distance between the vehicle and a detected object. |
L | 00:Keep Vol,01:L,10:M1,11:M2 |
Clearance warning ECU assembly | |
Temporary Mute Reset Speed Adjust |
Sets the vehicle speed at which the temporary mute function resets. |
20 km/h | 00:System Link,01:15km/h,10:20km/h,11:30km/h |
Clearance warning ECU assembly | |
Temporary Mute Function |
Sets the availability of the temporary mute function. |
ON | 0:OFF,1:ON |
Clearance warning ECU assembly | Sensor
|
Tester Display | Description |
Default | Setting |
ECU | | Sensor Condition N |
Makes the front sensors available when shift lever is in N. |
Avail | 0:Not Avail,1:Avail |
Clearance warning ECU assembly | Display
|
Tester Display | Description |
Default | Setting |
ECU | | Approach Display OFF |
Sets whether the display turns off after an obstacle is no longer detected. |
Avail | 0:Not Avail,1:Avail |
Clearance warning ECU assembly | |
Display Mode | The display mode setting (when the intuitive parking assist system is normal). |
All | 01:All,11:Undisp |
Clearance warning ECU assembly | Others
|
Tester Display | Description |
Default | Setting |
ECU | | ICS Function |
Intelligent clearance sonar system |
ON | 0:ON,1:OFF |
Clearance warning ECU assembly | |
ICS SW Status Memory | Intelligent clearance sonar system main switch memory function |
Yes | 0:Yes,1:No |
Clearance warning ECU assembly | |
ICS Stop Distance | Intelligent clearance sonar system target stopping distance |
Long | 0:Short,1:Long |
Clearance warning ECU assembly | |
RCTAB Function | Setting of the rear cross traffic auto brake function |
ON | 0:ON,1:OFF |
Clearance warning ECU assembly | |
RCTAB Operation Timing Setting |
Setting of the activation timing of the rear cross traffic auto brake function |
Standard | 0:Late,1:Standard |
Clearance warning ECU assembly | |
RCTAB Sensitivity | Setting of the sensitivity of the rear cross traffic auto brake function |
Standard | 0:Standard,1:Low |
Clearance warning ECU assembly | |
