DESCRIPTION The headlight ECU sub-assembly LH and headlight ECU sub-assembly RH internally boost the power supply voltage to ensure a constant supplied current for the low beam LED of their respective headlight. By monitoring the LED power supply voltage, abnormal current and malfunctions can be detected.
WIRING DIAGRAM ![]() CAUTION / NOTICE / HINT NOTICE:
PROCEDURE
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (e) Clear the DTCs. Body Electrical > HL AutoLeveling > Clear DTCs Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (f) Check for DTCs. Body Electrical > HL AutoLeveling > Trouble Codes Body Electrical > HL AutoLeveling (Sub) > Trouble CodesOK: DTC B2439 and B243A are not output.
(a) Remove each headlight ECU sub-assembly, interchange the headlight assembly LH with RH and connect the connectors. Click here
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (e) Clear the DTCs. Body Electrical > HL AutoLeveling > Clear DTCs Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (f) Check for DTCs. Body Electrical > HL AutoLeveling > Trouble Codes Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
(a) Remove each headlight ECU sub-assembly, interchange the headlight assembly RH with LH and connect the connectors. Click here
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (e) Clear the DTCs. Body Electrical > HL AutoLeveling > Clear DTCs Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes. (f) Check for DTCs. Body Electrical > HL AutoLeveling > Trouble Codes Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
|
Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Hybrid Control System: Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range (P0A9B2A,P0AC52A,P0ACA2A,P306562)
DESCRIPTION Refer to the description for DTC P0A9B11. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0A9B2A Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range The performance of battery temperature sensor 0 is abnormal and its output is stuck ...