REMOVAL CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization or
registration) that must be performed after parts are removed and
installed, or replaced during sliding roof housing removal/installation
are shown below. Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link | |
*: When performing learning using the Techstream.
Click here  | |
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
| |
Pre-collision System | |
Intelligent Clearance Sonar System* | |
Lighting System (for Gasoline Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking Assist Monitor System |
| |
Panoramic View Monitor System | |
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
- Sliding roof ECU (sliding roof drive gear sub-assembly)
- Sliding roof glass sub-assembly
- Sliding roof drive cable sub-assembly
- Sliding roof drive gear sub-assembly
| Initialize sliding roof system |
- Auto operation function
- Jam protection function
- Key-off operation function
- Key-linked function
- Wireless transmitter-linked function
- Sliding roof open warning function
|
| Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link | |
*: When performing learning using the Techstream.
Click here | |
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
| |
Pre-collision System | |
Intelligent Clearance Sonar System* | |
Lighting System (for HV Model with Cornering Light) | |
Memorize steering angle neutral point |
Parking Assist Monitor System |
| |
Panoramic View Monitor System | |
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
- Sliding roof ECU (sliding roof drive gear sub-assembly)
- Sliding roof glass sub-assembly
- Sliding roof drive cable sub-assembly
- Sliding roof drive gear sub-assembly
| Initialize sliding roof system |
- Auto operation function
- Jam protection function
- Key-off operation function
- Key-linked function
- Wireless transmitter-linked function
- Sliding roof open warning function
|
| CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
 for Gasoline Model: Click here
for HV Model: Click here
PROCEDURE 1. REMOVE SLIDING ROOF SIDE GARNISH LH
| (a) Disengage the 4 claws to remove the sliding roof side garnish LH. |
|
2. REMOVE SLIDING ROOF SIDE GARNISH RH HINT: Use the same procedure as for the LH side.
3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY (a) Move the sliding roof glass sub-assembly to the fully closed position.
(b) Using a T25 "TORX" socket wrench, remove the 4 screws and sliding roof glass sub-assembly.
 NOTICE: To
prevent the sliding roof glass sub-assembly and sliding roof drive gear
assembly from becoming misaligned, move the sliding roof glass
sub-assembly (sliding roof drive cable sub-assembly) to the fully closed
position before removing it. 4. REMOVE SLIDING ROOF WEATHERSTRIP
| (a) Remove the sliding roof weatherstrip from the sliding roof panel sub-assembly. |
|
5. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH Click here
6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH
HINT: Use the same procedure as for the LH side. 7. DISCONNECT SLIDING ROOF DRAIN HOSE
HINT: Use the same procedure for all of the sliding roof drain hoses.
(a) for Clamp Type: | (1) Disengage the claw and disconnect the sliding roof drain hose. |
|
(b) for Clip Type: | (1) Expand the clip and disconnect the sliding roof drain hose. |
|
8. REMOVE SLIDING ROOF HOUSING ASSEMBLY (a) Remove the 8 bolts, 6 nuts and sliding roof housing assembly.
 | 
