DESCRIPTION The sliding
roof ECU (sliding roof drive gear assembly) receives slide and tilt
signals and operates its built-in motor when the sliding roof switch
(roof console box sub-assembly) is operated. WIRING DIAGRAM
 CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- If the sliding roof ECU (sliding roof drive gear assembly) is removed
and reinstalled or replaced, the sliding roof ECU (sliding roof drive
gear assembly) must be initialized.
Click here 
- If a sliding roof ECU (sliding roof drive gear assembly) DTC is output,
first perform troubleshooting for the sliding roof ECU (sliding roof
drive gear assembly) DTC.
Click here
PROCEDURE |
1. | PERFORM ACTIVE TEST USING TECHSTREAM (SLIDE ROOF) |
(a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG).
(c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Slide Roof / Active Test.
(e) Perform the Active Test according to the display on the Techstream. Body Electrical > Sliding Roof > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note | |
Slide Roof | Operate sliding roof motor |
OFF / Opn/Dwn / Clos/Up |
- | Body Electrical > Sliding Roof > Active Test
|
Tester Display | | Slide Roof |
OK: Slide roof is operated using Techstream.
| NG |
 | GO TO STEP 5 |
|
OK |
 | |
| 2. |
READ VALUE USING TECHSTREAM | (a) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(b) Read the Data List according to the display on the Techstream. Body Electrical > Sliding Roof > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note | |
Open Switch | OPEN switch signal |
OFF or ON | OFF: OPEN switch not pressed
ON: OPEN switch pressed |
- | | Close Switch |
CLOSE switch signal | OFF or ON |
OFF: CLOSE switch not pressed ON: CLOSE switch pressed |
- | | Up Switch |
UP switch signal | OFF or ON |
OFF: UP switch not pressed ON: UP switch pressed |
- | | Down Switch |
DOWN switch signal | OFF or ON |
OFF: DOWN switch not pressed ON: DOWN switch pressed |
- | Body Electrical > Sliding Roof > Data List
|
Tester Display | | Open Switch | |
Close Switch | | Up Switch | |
Down Switch | OK: The Techstream display changes according to the operation of each switch as shown in the table.
| OK |
| REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
|
NG | |
| |
| 3. |
INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Remove the sliding roof switch (roof console box sub-assembly). Click here
(b) Inspect the sliding roof switch (roof console box sub-assembly).
Click here
| NG |
| REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) |
|
OK | |
| |
| 4. |
CHECK
HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR
ASSEMBLY) - SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY
GROUND) | (a) Disconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
O3-8 (CLS) - O10-4 (CLS) |
Always | Below 1 Ω | |
O3-8 (CLS) or O10-4 (CLS) - Body ground |
Always | 10 kΩ or higher | |
O3-10 (OPN) - O10-5 (OPN) |
Always | Below 1 Ω | |
O3-10 (OPN) or O10-5 (OPN) - Body ground |
Always | 10 kΩ or higher | |
O3-9 (DWN) - O10-18 (DOWN) |
Always | Below 1 Ω | |
O3-9 (DWN) or O10-18 (DOWN) - Body ground |
Always | 10 kΩ or higher | |
O3-5 (UP) - O10-3 (UP) |
Always | Below 1 Ω | |
O3-5 (UP) or O10-3 (UP) - Body ground |
Always | 10 kΩ or higher | |
O10-15 (GND) - Body ground |
Always | Below 1 Ω | |
O3-2 (E) - Body ground |
Always | Below 1 Ω |
| OK |
| REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 5. |
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - IG POWER SUPPLY AND BODY GROUND) |
| (a) Disconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector. |
 |
|
*a | Front view of wire harness connector
(to Sliding Roof ECU (Sliding Roof Drive Gear Assembly)) | | |
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage: |
Tester Connection | Condition |
Specified Condition | |
O3-6 (IG) - Body ground |
Power switch on (IG) |
11 to 14 V | |
O3-6 (IG) - Body ground |
Power switch off | Below 1 V |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
O3-2 (E) - Body ground |
Always | Below 1 Ω |
| OK |
| REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR | | 
