Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

• Use the same procedure for the RH side and LH side.
• The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. INSTALL FRONT DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE

(a) Install the front door inside lock/unlock knob locking cable as shown in the illustration.

Install in this Direction

3. INSTALL FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE

(a) Install the front door lock open lever remote control cable as shown in the illustration.

Install in this Direction

(b) Engage the 3 claws to close the cover as shown in the illustration.

4. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:

• When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.
• Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
• Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.

(a) Apply MP grease to the sliding parts of the front door lock with motor assembly.

(b) When reusing the front door lock with motor assembly:

(1) Install a new door lock wiring harness seal to the front door lock with motor assembly.

(c) Connect the front door lock open rod to the front door lock with motor assembly.

*1	Front Door Lock Open Rod
	Install in this Direction

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.

(d) Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:

5.5 N·m {56 kgf·cm, 49 in·lbf}

(e) Connect the connector.

5. INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Click here

6. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Click here

7. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Click here

8. INSTALL FRONT DOOR GLASS RUN

Click here

9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Click here

10. INSTALL FRONT DOOR VENT SEAL

Click here

11. INSTALL FRONT DOOR PANEL PROTECTOR

Click here

12. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

Click here

13. INSTALL FRONT DOOR SERVICE HOLE COVER

Click here

14. INSTALL FRONT DOOR TRIM BRACKET

Click here

15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here

16. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

17. INSTALL COURTESY LIGHT ASSEMBLY

Click here

18. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

19. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

20. INSTALL FRONT DOOR TRIM POCKET COVER

Click here

21. INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

23. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

24. INITIALIZE POWER WINDOW CONTROL SYSTEM

for Gasoline Model:

Click here

for HV Model:

Click here

25. INSPECT POWER WINDOW OPERATION

for Gasoline Model:

Click here

for HV Model:

Click here