DESCRIPTION The combination
meter assembly receives vehicle speed signals from the skid control ECU
(brake actuator assembly) via CAN communication. The speed sensor
detects the wheel speed and sends the appropriate signals to the skid
control ECU (brake actuator assembly). The skid control ECU (brake
actuator assembly) supplies power to the vehicle speed sensor. The skid
control ECU (brake actuator assembly) detects vehicle speed signals
based on pulses of the voltage. HINT: Factors
that affect the indicated vehicle speed include the tire size, tire
inflation, and tire wear. The speed indicated on the speedometer has an
allowable margin of error. WIRING DIAGRAM
 CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE |
1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Check if CAN communication DTCs are output. Click here
 |
Result | Proceed to | |
DTCs are not output | A | |
DTCs are output | B |
| B |
 | GO TO CAN COMMUNICATION SYSTEM |
|
A |
 | |
| 2. |
CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM) |
(a) Check if electronically controlled brake system DTCs are output. Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
|
Result | Proceed to | |
DTCs are not output | A | |
DTCs are output | B |
| B |
| GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM |
|
A | |
| |
| 3. |
PERFORM ACTIVE TEST USING TECHSTREAM | (a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG). (c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Perform the Active Test according to the display on the Techstream. Body Electrical > Combination Meter > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note | |
Speedometer Operation (0km/h,0MPH) |
Speedometer (0 km/h, 0 mph) |
ON | - | |
Speedometer Operation (40km/h,40MPH) |
Speedometer (40 km/h, 40 mph) |
ON | The value displayed on the speedometer may deviate.
Reference mph*1: 40 → 39.4 to 42.2 Reference km/h*2:
40 → 38.7 to 43.2 | |
Speedometer Operation (80km/h,80MPH) |
Speedometer (80 km/h, 80 mph) |
ON | The value displayed on the speedometer may deviate.
Reference mph*1: 80 → 80.0 to 83.2 Reference km/h*2:
80 → 79.3 to 84.3 | |
Speedometer Operation (120km/h,120MPH) |
Speedometer (120 km/h, 120 mph) |
ON | The value displayed on the speedometer may deviate.
Reference mph*1: 120 → 120.9 to 124.1 Reference km/h*2:
120 → 120.3 to 125.3 | |
Speedometer Operation (160km/h,160MPH) |
Speedometer (160 km/h, 160 mph)*2 |
ON | The value displayed on the speedometer may deviate.
Reference km/h*2: 160 → 161.2 to 166.2 | |
Speedometer Operation (200km/h,200MPH) |
Speedometer (200 km/h, 200 mph)*2 |
ON | The value displayed on the speedometer may deviate.
Reference km/h*2: 200 → 202.1 to 207.1 | |
Speedometer Operation (240km/h,240MPH) |
Speedometer (240 km/h, 240 mph)*2 |
ON | The value displayed on the speedometer may deviate.
Reference km/h*2: 240 → 243.0 to 248.0 |
- *1: for Speedometer with Imperial Units for Main Scale
- *2: for Speedometer with Metric Units for Main Scale
Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (0km/h,0MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (40km/h,40MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (80km/h,80MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (120km/h,120MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (160km/h,160MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (200km/h,200MPH) | Body Electrical > Combination Meter > Active Test
|
Tester Display | | Speedometer Operation (240km/h,240MPH) |
OK: Speedometer indication is normal.
| OK |
| REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
| NG |
| REPLACE COMBINATION METER ASSEMBLY | |
