Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Steering Pad Switch Circuit

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Interior / Meter / Gauge / Display / Meter / Gauge System(for Gasoline Model) / Steering Pad Switch Circuit

DESCRIPTION

The combination meter assembly and steering pad switch assembly are connected via direct line. The multi-information display in the combination meter assembly are operated using the switches of the steering pad switch assembly.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.

INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly.

Click here

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

OK

2.

INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Remove the spiral cable sub-assembly.

Click here

(b) Inspect the spiral cable sub-assembly.

Click here

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

OK

3.

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the G16 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G17-11 (+DP) - G16-29 (MSTI)

Always

Below 1 Ω

G17-10 (+DP2) - G16-28 (MSM+)

Always

Below 1 Ω

G17-11 (+DP) or G16-29 (MSTI) - Body ground

Always

10 kΩ or higher

G17-10 (+DP2) or G16-28 (MSM+) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

*a

Front view of wire harness connector

(to Spiral Cable Sub-assembly)

(a) Connect the G16 combination meter assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

G17-11 (+DP) - Body ground

Engine switch on (IG)

4.8 to 5.2 V

G17-10 (+DP2) - Body ground

Engine switch on (IG)

4.8 to 5.2 V
NG

REPLACE COMBINATION METER ASSEMBLY

OK

5.

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Disconnect the G3 radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G17-4 (EAU) - G3-24 (SWG)

Always

Below 1 Ω
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

6.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G3-1 (GND1) - Body ground

Always

Below 1 Ω
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
    Speedometer Malfunction

    System Description

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Motor Generator Control System: Dtc Check / Clear
    DTC CHECK / CLEAR CHECK FOR DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Motor Generator / Trouble Codes. Powertrain > Motor Generator > Trouble Codes (e) Check the DTCs and freeze frame d ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2025 Copyright www.tavalon.net
    0.0131