Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR SEAT BELT RETRACTOR COVER LH

(a) Install the rear seat belt retractor cover LH as shown in the illustration.

Install in this Direction

2. INSTALL REAR SEAT BELT RETRACTOR COVER RH

HINT:

Use the same procedure as for the LH side.

3. INSPECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

Click here

4. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

(a) Engage the guide and temporarily install the rear seat 3 point type belt assembly LH with the 2 bolts.

(b) Fully tighten the bolt (A), and then the bolt (B) to install the rear seat 3 point type belt assembly LH.

Torque:

Bolt (A) :

12.5 N·m {127 kgf·cm, 9 ft·lbf}

Bolt (B) :

42 N·m {428 kgf·cm, 31 ft·lbf}

(c) Connect the pretensioner connector and lock the locking button as shown in the illustration. NOTICE: Securely lock the locking button.

*a Locking Button *b Lock

(d) Check that the ELR locks.

NOTICE:

This check should be performed with the rear seat outer belt assembly LH installed to the vehicle.

(1) With the rear seat 3 point type belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.

5. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

(a) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

(b) Engage the 3 clips and 5 guides.

(c) Install the package tray trim panel assembly with the 2 clips.

(d) Return the rear seatback assembly LH and rear seatback assembly RH to their original position.

7. INSTALL REAR SEAT SHOULDER BELT COVER

(a) Engage the 2 guides and 2 claws to install the rear seat shoulder belt hole cover.

HINT:

Use the same procedure for the other rear seat shoulder belt hole covers.

8. INSTALL CENTER STOP LIGHT SET

Click here

9. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

(a) Install the floor anchor of the rear seat outer belt assembly LH with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

NOTICE:

Do not allow the anchor part of the rear seat outer belt assembly LH to overlap the protruding parts of the floor panel.

Protruding Part

10. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

11. INSTALL ROOF SIDE INNER GARNISH LH

Click here

12. INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

13. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

Click here

14. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

16. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

Click here

17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

Click here

18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

19. INSTALL REAR SEAT CUSHION LOCK HOOK

Click here

20. INSTALL REAR SEAT CUSHION ASSEMBLY

Click here

21. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Click here

22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

23. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)

Click here

24. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)

Click here

25. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

26. PERFORM DIAGNOSTIC SYSTEM CHECK

for HV Model:

Click here

for Gasoline Model:

Click here

27. INSPECT SRS WARNING LIGHT

for HV Model:

Click here

for Gasoline Model:

Click here