Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the engine switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the engine switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.

(g) According to the display on the Techstream, read the Data List.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS warning light

ON or OFF

ON: Warning light on

OFF: Warning light off

-

Brake Warning Light

Brake system warning light (red indicator)

ON or OFF

ON: Warning light on

OFF: Warning light off

-

Stop Light SW

Stop light switch assembly

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Parking Brake SW

Parking brake switch assembly

ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

Main Idle SW

Main idle switch

ON or OFF

ON: Accelerator pedal released

OFF: Accelerator pedal depressed

-

Gear Position

Gear position information

"P,N", R, 1st-10th, Fail or Not R

Actual gear position

-

Shift Lever Position

Shift lever position information

"P,N", R, D/M, 1st-6th/B or Fail

Actual shift lever position

-

Shift Information

Shift information

ON or OFF

ON: During gear change

OFF: Not during gear change

-

Inspection Mode

Inspection mode

Other or Inspect

Other: Normal mode

Inspect: Inspection mode

-

Number of IG ON(Inspection)

Number of times engine switch turned on (IG) after entering inspection mode

Min.: 0, Max.: 255

-

-

Master Cylinder Sensor

Master cylinder pressure sensor reading

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 0.20 to 0.40 V

Reading increases when brake pedal is depressed

Deceleration Sensor

Acceleration sensor reading

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Deceleration Sensor2

Acceleration sensor 2 reading

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele2

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Yaw Rate Sensor

Yaw rate sensor

Min.: -128°/s, Max.: 127°/s

Vehicle stopped: 0°/s

Turning right: -128 to 0°/s

Turning left: 0 to 127°/s

-

Zero Point of Yaw Rate

Memorized zero value

Min.: -128°, Max.: 127°

-

After completing zero point calibration: 0°

Steering Angle Sensor

Steering angle sensor

Min.: -3276.8°, Max.: 3276.7°

Turning left: Increases

Turning right: Decreases

-

Zero Point of Steering Angle

Memorized zero value

Min.: -3276.8°, Max.: 3276.7°

-

After steering angle sensor zero point calibration: 0°

Lateral G

Lateral G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During turning: Changes in proportion with lateral acceleration

Forward and Rearward G

Forward and rearward G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During acceleration/deceleration: Changes in proportion with acceleration

Yaw Rate Value

Yaw rate value

Min.: -128°/s, Max.: 127°/s

-

During turning: Changes in proportion with yaw

Steering Angle Value

Steering angle value

Min.: -3276.8°, Max.: 3276.7°

-

During steering operation: Changes in proportion with steering wheel rotation

Stop Light Relay

Stop light control relay (Stop light switch assembly)

(STP2 terminal input)

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Slip Indicator Light

Slip indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

FR Wheel Speed

Front wheel speed sensor RH reading

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FL Wheel Speed

Front wheel speed sensor LH reading

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RR Wheel Speed

Rear wheel speed sensor RH reading

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear wheel speed sensor LH reading

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

Vehicle Speed

Maximum wheel speed sensor reading

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FR Wheel Acceleration

Front wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

FL Wheel Acceleration

Front wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RR Wheel Acceleration

Rear wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RL Wheel Acceleration

Rear wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

Stop Light Relay Output

Stop light control relay (Stop light switch assembly)

(STPO terminal output)

ON or OFF

ON: Relay output on

OFF: Relay output off

-

EBS Relay

Stop light control relay (Stop light switch assembly) (for emergency brake signal)

ON or OFF

OFF: Relay off

Not applicable to this vehicle

FR Wheel ABS Ctrl Status

Front wheel RH ABS control status

ON or OFF

ON: During control

-

FL Wheel ABS Ctrl Status

Front wheel LH ABS control status

ON or OFF

ON: During control

-

RR Wheel ABS Ctrl Status

Rear wheel RH ABS control status

ON or OFF

ON: During control

-

RL Wheel ABS Ctrl Status

Rear wheel LH ABS control status

ON or OFF

ON: During control

-

FR Wheel EBD Ctrl Status

Front wheel RH EBD control status

ON or OFF

ON: During control

-

FL Wheel EBD Ctrl Status

Front wheel LH EBD control status

ON or OFF

ON: During control

-

RR Wheel EBD Ctrl Status

Rear wheel RH EBD control status

ON or OFF

ON: During control

-

RL Wheel EBD Ctrl Status

Rear wheel LH EBD control status

ON or OFF

ON: During control

-

BA Ctrl Status

BA control status

ON or OFF

ON: During control

-

PBA Ctrl Status

PBA control status

ON or OFF

ON: During control

-

TRC(TRAC) Ctrl Status

TRAC control status

ON or OFF

ON: During control

-

TRC(TRAC) Engine Ctrl Status

TRAC engine control status

ON or OFF

ON: During control

-

TRC(TRAC) Brake Ctrl Status

TRAC brake control status

ON or OFF

ON: During control

-

FR Wheel VSC Ctrl Status

Front wheel RH VSC control status

ON or OFF

ON: During control

-

FL Wheel VSC Ctrl Status

Front wheel LH VSC control status

ON or OFF

ON: During control

-

RR Wheel VSC Ctrl Status

Rear wheel RH VSC control status

ON or OFF

ON: During control

-

RL Wheel VSC Ctrl Status

Rear wheel LH VSC control status

ON or OFF

ON: During control

-

Engine Revolutions

Engine speed

Min.: 0 rpm, Max.: 65535 rpm

Engine stopped: 0 rpm

When engine speed is constant: No large fluctuations

Real Engine Torque

Real engine torque

Min.: -1024 Nm, Max.: 1023 Nm

-

-

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle

Min.: 0.0%, Max.: 127.5%

Accelerator pedal released: 0.0%

During accelerator pedal operation: Changes in proportion with the pedal movement

Solenoid Relay

ABS solenoid relay

ON or OFF

ON: ABS solenoid relay on

OFF: ABS solenoid relay off

-

TR(A)C/VSC Solenoid (SRM2)

Master cut solenoid (SRM2)

ON or OFF

ON: During control

-

TR(A)C/VSC Solenoid (SRM1)

Master cut solenoid (SRM1)

ON or OFF

ON: During control

-

TR(A)C/VSC Solenoid (SRC2)

Master cut solenoid (SRC2)

ON or OFF

ON: During control

-

TR(A)C/VSC Solenoid (SRC1)

Master cut solenoid (SRC1)

ON or OFF

ON: During control

-

ABS Solenoid (SFRH)

ABS solenoid (SFRH)

ON or OFF

ON: During control

-

ABS Solenoid (SFRR)

ABS solenoid (SFRR)

ON or OFF

ON: During control

-

ABS Solenoid (SFLH)

ABS solenoid (SFLH)

ON or OFF

ON: During control

-

ABS Solenoid (SFLR)

ABS solenoid (SFLR)

ON or OFF

ON: During control

-

ABS Solenoid (SRRH)

ABS solenoid (SRRH)

ON or OFF

ON: During control

-

ABS Solenoid (SRRR)

ABS solenoid (SRRR)

ON or OFF

ON: During control

-

ABS Solenoid (SRLH)

ABS solenoid (SRLH)

ON or OFF

ON: During control

-

ABS Solenoid (SRLR)

ABS solenoid (SRLR)

ON or OFF

ON: During control

-

EFI Communication Open

ECM communication open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Yaw Rate Open

Yaw rate sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Deceleration Open

Acceleration sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Steering Open

Steering angle sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

IG1 Voltage Value

IG1 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to battery voltage

BS1 Voltage Value

+BS voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to battery voltage

MT Voltage Value

Motor voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to battery voltage

BH Standby Light

Brake hold standby indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

TRAC/VSC Off Mode

TRAC/VSC off mode

Normal, TRC OFF,VSC Expert Mode or VSC OFF

Normal: Normal mode

TRC OFF: TRAC off mode

VSC Expert Mode: VSC expert mode

VSC OFF: VSC off mode

-

Number of DTC

Number of DTC recorded

Min.: 0, Max.: 255

-

-

IG Voltage Value Decreased

+BS voltage value decrease detection

Error or Normal

Error: Voltage low

Normal: Normal

-

IG Voltage Value Increased

+BS voltage value increase detection

Error or Normal

Error: Voltage high

Normal: Normal

-

Brake Hold Ready

Brake hold control permission status

OFF or ON

ON: Brake hold control permitted

OFF: Brake hold control not permitted

-

Brake Hold Control Mode

Brake hold control mode

OFF, ON, Release or EPB

OFF: Brake hold control is not operating

ON: Brake hold control is operating

Release: Brake hold control is released

EPB: Parking brake is engaged during brake hold control

HINT:

EPB stands for electric parking brake.

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.

Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the engine switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the engine switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

Chassis > ABS/VSC/TRAC/EPB > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

ABS Warning Light

ABS warning light

Warning light OFF/ON

Observe combination meter assembly

Brake Warning Light

Brake system warning light (red indicator)

Warning light OFF/ON

Observe combination meter assembly

Motor Relay

ABS motor relay

Relay OFF/ON

Operating sound of motor can be heard

Stop Light Relay

Stop light control relay (Stop light switch assembly)

Relay OFF/ON

Stop lights come on

ABS Solenoid (SRLR)

ABS solenoid (SRLR)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SRLH)

ABS solenoid (SRLH)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SRRR)

ABS solenoid (SRRR)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SRRH)

ABS solenoid (SRRH)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SFLR)

ABS solenoid (SFLR)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SFLH)

ABS solenoid (SFLH)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SFRR)

ABS solenoid (SFRR)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

ABS Solenoid (SFRH)

ABS solenoid (SFRH)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

VSC/TRAC Solenoid (SRMR)

Master cut solenoid (SRM2)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

VSC/TRAC Solenoid (SRMF)

Master cut solenoid (SRM1)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

VSC/TRAC Solenoid (SRCR)

Master cut solenoid (SRC2)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

VSC/TRAC Solenoid (SRCF)

Master cut solenoid (SRC1)

Solenoid ON/OFF

Operation sound of solenoid (clicking sound) can be heard

BH Standby Light

Brake hold standby indicator light

Indicator light OFF/ON

  • Observe combination meter assembly
  • Perform the Active Test with the vehicle stopped

BH Operated Light

Brake hold operated indicator light

Indicator light OFF/ON

  • Observe combination meter assembly
  • Perform the Active Test with the vehicle stopped

TRC(TRAC) OFF Indicator Light

Multi-information display (Traction Control Turned Off)

Display OFF/ON

Observe combination meter assembly

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light OFF/ON

Observe combination meter assembly

Slip Indicator Light

Slip Indicator light

Indicator light OFF/ON

Observe combination meter assembly

EBS Relay

Stop light switch assembly output (Emergency brake signal operation)

OFF/ON

Not applicable to this vehicle

ABS Solenoid

ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH)

Solenoid SRLR/SRLH/SRRR/

SRRH/SFLR/SFLH/SFRR/SFRH

Operation sound of solenoid (clicking sound) can be heard

VSC/TRC(TRAC) Solenoid

Master cut solenoid (SRM1, SRM2, SRC1, SRC2)

Solenoid SRMF/SRMR/SRCF/

SRCR/SMF/SMR/SPFR/SPFL

Operation sound of solenoid (clicking sound) can be heard

    Check For Intermittent Problems

    Diagnosis System

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Meter / Gauge System(for Hv Model): Data List / Active Test
    DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or states of ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0118